Hand Held Products 5700 Reread Delay Selection, Good Read Delay Selection, Laser Voting Selection

Page 33

Reread Delay Selection

This selection allows you to set a time period that must pass before the scanner can read the same bar code again. Setting a reread delay protects against accidental rereads of the same bar code. Longer delays are effective in minimizing accidental rereads at POS (point of sale) terminals. Use shorter delays in applications where repetitive bar code scanning is required.

Low (175 milliseconds)

Medium (450 milliseconds)

High (1.0 second)

Extra High (2.0 seconds)

Good Read Delay Selection

This selection allows you to set a time period that must pass before the scanner can read another bar code. Some terminals require a slower read rate. By setting a good read delay, you can ensure a good read.

None

Low (500 milliseconds)

Medium (1.0 second)

High (1.5 second)

Laser Voting Selection

When Laser Voting is enabled, the scanner requires three (3) identical, consecutive scans before the bar code data will be accepted and transmitted to the terminal. When this selection is disabled, the bar code data will be transmitted following one (1) valid scan.

Enable

Disable

SCANTEAM 5700 User’s Guide

2–9

Image 33
Contents Decoded Output Disclaimer FCC Class B Compliance Statement Scanteam 5700 User’s GuideCanadian Notice A. StatementPatents Table of Contents Require Data Format Data Format Editor Protocol Selection Serial Wedge Output SelectionMarker Beam Selection AutoTrigger Selection Foreign Keyboard SelectionKeyboard Function Relationships Supported Interface Keys Industrial Symbology SelectionsObtaining Factory Service Technical Support Maintenance TroubleshootingIntroduction Scanner Identification Model Number 5X00/A-12Cable, Keyboard, and Terminal will vary Connecting the ScannerScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC, Wand Emulation Interface IBM PC AT and Compatibles Interface DefaultIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles InterfaceIBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Notes Dual Interface Programming InstructionsSame Code Wand Emulation Selection Code 39 Wand Emulation SelectionRS-232 Selection Laser Emulation SelectionDual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Suffix Selection Secondary Interface Prefix SelectionExample 2 Add Suffix for ALL Symbologies Example 1 Add Suffix for Specific SymbologyPrefix and Suffix Examples Example 4 To Clear a Specific Prefix EntryValue Symbology Code HexOutput Delays Selection Beeper Volume SelectionReread Delay Selection Good Read Delay SelectionLaser Voting Selection Code I.D. Transmit Selection Buffered Scans SelectionAIM I.D. Transmit Selection Function Code Transmit SelectionBaud Rate Selection CTS Check SelectionParity Selection RS-232 Word Length SelectionSerial Wedge Output Selection Protocol Selection➋ Terminal Type ➎ Editor Command Sequences➌ Code I.D ➍ LengthData Format Editor Require Data FormatMove Commands Send CommandsSearch Commands Miscellaneous CommandsUPC a with 5 digit addenda Data Formatter ExampleScanteam 5700 User’s Guide Introduction AutoTrigger Selection Marker Beam SelectionTransmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection NCR 7052 Keypad Selection AT Direct Connect SelectionKeyboard Style Keyboard Style SelectionsKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Message Length Codabar SelectionCheck Character Append Code 39 SelectionMinimum Maximum Code 93 Selection Full Ascii ChartCheck Digit Interleaved 2 of 5 SelectionMatrix 2 of 5 Selection Code 2 of 5 SelectionCode 128 Selection Code 11 SelectionCode 128 Function Character Selection Code 49 Selection Code 16K SelectionIsbn EAN SelectionUPC E1 UPC SelectionUPC Addenda Selection EAN Addenda SelectionPlessey Selection MSI SelectionScanteam 5700 User’s Guide Page Memory Upload Scanteam 5700 User’s Guide Download New FirmwareClone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris Telex IBM, MemorexAnsi Ascii Supported Esprit 200Bull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only Pin Type D Female 5700-X4 Laser Compatible Bar Image +12VDC InputWand Emulation RS-232 Laser Output Cleaning the Scan Window MaintenanceReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Welch Allyn, Inc Obtaining Factory ServiceWelch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Output Selections Serial Interface Menu DefaultsKeyboard Selections General Operating Menu DefaultsCodabar Selections Symbology Menu Defaults IndustrialCode 11 Selections EAN / UPC Addenda Selections Symbology Menu Defaults RetailScanteam 5700 User’s Guide Page Page Page Interleaved 2 EANMatrix 2 Code 2