Hand Held Products 5700 manual Primary Interface Prefix and Suffix

Page 26

Primary Interface Prefix and Suffix

The scanner transmits a decoded message after every successful bar code read. Prefix and Suffix characters are data characters you may assign to be sent before and after the transmitted bar code data.

Transmitted data frame –>

Prefix

Bar Code Message

Suffix

Characters for the Prefix and Suffix are selected by their hexadecimal ASCII value, up to 12 characters each. Prefix and Suffix characters may be sent for a specific symbology, or may be sent with all bar code scans.

Default Prefix = none. Default Suffix = none.

Programming Steps to Add a Primary Interface Prefix / Suffix:

➊To add a Prefix, scan the Add Primary Prefix programming bar code. To add a Suffix, scan the Add Primary Suffix programming bar code.

➋Refer to the Symbology Chart (page 2–7) to find the Hex value that represents the symbology(s) you want transmitted with one or more Prefixes or Suffixes. Scan the two digits on the Programming Chart (on the inside of the back cover of this menu).

➌Refer to the Hex ASCII Chart (page 2–7) to find the Hex value that represents the ASCII characters you wish to transmit with the bar code data. Use the Programming Chart (inside back cover) to scan the alphanumeric combination that represents the ASCII characters.

➍To complete Prefix / Suffix programming, scan either:

H Save Current Prefix or Suffix Changes[ programming bar code. This exits, saving the Prefix / Suffix selections you just assigned.

H Discard Current Prefix or Suffix Changes programming bar code. This exits without changing the Prefix / Suffix.

[You may also start scanning bar codes; your Prefix / Suffix selections will be saved.

Programming Steps to Clear (or Delete) One Prefix / Suffix Entry:

➊To clear the Prefix entry for a specific symbology, scan the Clear One Primary Prefix programming bar code.

To clear the Suffix entry for a specific symbology, scan the Clear One Primary Suffix programming bar code.

➋Refer to the Symbology Chart to find the Hex value representing the symbology’s entry you want cleared. Scan the two digits on the Programming Chart (on the inside of the back cover of this menu).

➌You don’t need to scan Save Current ... Changes or Discard Current

... Changes programming bar codes to complete programming.

Other Programming Selections: Scanning the Clear All Primary Prefixes or Clear All Primary Suffixes bar code deletes all Primary Prefix or Suffix selections. You don’t need to scan the Save Current ... Changes or Discard Current ... Changes programming bar code to complete programming.

Note: Prefix / Suffix programming examples may be found on page 2–6.

2–2

SCANTEAM 5700 User’s Guide

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Decoded Output Disclaimer Canadian Notice Scanteam 5700 User’s GuideFCC Class B Compliance Statement A. StatementPatents Table of Contents Marker Beam Selection AutoTrigger Selection Protocol Selection Serial Wedge Output SelectionRequire Data Format Data Format Editor Foreign Keyboard SelectionIndustrial Symbology Selections Keyboard Function Relationships Supported Interface KeysMaintenance Troubleshooting Obtaining Factory Service Technical SupportIntroduction Model Number 5X00/A-12 Scanner IdentificationConnecting the Scanner Cable, Keyboard, and Terminal will varyScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PS/2 and Compatibles Interface IBM PC AT and Compatibles Interface DefaultIBM PC, Wand Emulation Interface IBM PC XT and Compatibles InterfaceCode IBM 4683 InterfaceCode EAN Ocia Interface OCR, RS232 Interface Terminal Models Terminal I.D Supported TerminalsProgram Terminal Interface ICL Quick Suffix Selections Reset Factory SettingsStatus Check Dual Interface Programming Instructions Dual Interface Programming NotesRS-232 Selection Code 39 Wand Emulation SelectionSame Code Wand Emulation Selection Laser Emulation SelectionLaser Emulation Power Up Delay Selection Dual Interface Enable/Disable SelectionSwitched Power Mode Selections Introduction Primary Interface Prefix and Suffix Exit Selection for Prefix / Suffix Primary Interface Prefix SelectionPrimary Interface Suffix Selection Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix SelectionPrefix and Suffix Examples Example 1 Add Suffix for Specific SymbologyExample 2 Add Suffix for ALL Symbologies Example 4 To Clear a Specific Prefix EntrySymbology Code Hex ValueBeeper Volume Selection Output Delays SelectionLaser Voting Selection Reread Delay SelectionGood Read Delay Selection AIM I.D. Transmit Selection Buffered Scans SelectionCode I.D. Transmit Selection Function Code Transmit SelectionCTS Check Selection Baud Rate SelectionRS-232 Word Length Selection Parity SelectionProtocol Selection Serial Wedge Output Selection➌ Code I.D ➎ Editor Command Sequences➋ Terminal Type ➍ LengthRequire Data Format Data Format EditorSearch Commands Send CommandsMove Commands Miscellaneous CommandsData Formatter Example UPC a with 5 digit addendaScanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger SelectionOutput Polarity Selection Transmission Rate SelectionWake Up Pulse Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad SelectionKeyboard Style Selections Keyboard StyleKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message LengthCheck Character Code 39 Selection AppendMinimum Maximum Full Ascii Chart Code 93 SelectionInterleaved 2 of 5 Selection Check DigitCode 2 of 5 Selection Matrix 2 of 5 SelectionCode 11 Selection Code 128 SelectionCode 128 Function Character Selection Code 16K Selection Code 49 SelectionEAN Selection IsbnUPC Selection UPC E1EAN Addenda Selection UPC Addenda SelectionMSI Selection Plessey SelectionScanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s Guide+ a Scanteam 5700 User’s Guide Clone DestinationClone Master Scanteam 5700 User’s Guide Country Codes Keyboard Function RelationshipsFunction Code HEX/ASCII Value Full Ascii Ctrl + Compatibles Harris IBM AT/XTPS/2 Compatibles, IBM XTs Memorex Telex IBM, Memorex TelexSupported Esprit 200 Ansi AsciiHDS-7 HP 700/92 Keyboards Bull BDS-7 Wyse WY-60/150Honeywell Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D FemaleWand Emulation RS-232 Laser Output Maintenance Cleaning the Scan WindowReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, IncEurope Welch AllynNorth America Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output SelectionsGeneral Operating Menu Defaults Keyboard SelectionsSymbology Menu Defaults Industrial Codabar SelectionsCode 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda SelectionsScanteam 5700 User’s Guide Page Page Page Matrix 2 EANInterleaved 2 Code 2
Top Page Image Contents