Hand Held Products 5700 manual Laser Output only

Page 78

Laser Output only

5700–X0

(Laser Compatible Bar Image)

Conventional laser data format is provided at the modular connector in the scanner handle.

Interface cables normally supplied with scanner model 5700–X0 are terminated with an 10 pin modular plug (P1) and a 9 pin Type D (Squeeze–to–release) connector (P2) that is compatible with all Welch Allyn terminals. See chart below.

P1

P2

	10 Pin Modular Plug		9 Pin Type D Female
	P1 connects to the		P2 connects to
	scanner handle.			your terminal.
		Pin 1	5		1
		Pin 10	9	View A–A	6


	P1	Signal	Function		P2
	9	SOS	Start of Scan		1
		Data	Digital Bar Code Data Output
	6				2
		Good Read	Turn on Good Read LED or Beeper
	5				3
		+5VDC	5 Volt Power Connection	♦
	7				9
		Trigger	Trigger Signal to Decoder
	8				5

	3	Enable	Laser Enable		6
		Ground	Supply Ground
	4				7
		Braid	Cord Shield
	2				8
			N/C	♦
					4

♦Pins 4 and 9 are populated depending on power supply voltage option.

Note: Some decoders may have +12V on pins 4 or 9. Connect to +5VDC

ONLY!

7–2	SCANTEAM 5700 User’s Guide

Image 78

Contents Decoded Output Disclaimer Canadian Notice Scanteam 5700 User’s GuideFCC Class B Compliance Statement A. StatementPatents Table of Contents Marker Beam Selection AutoTrigger Selection Protocol Selection Serial Wedge Output SelectionRequire Data Format Data Format Editor Foreign Keyboard SelectionIndustrial Symbology Selections Keyboard Function Relationships Supported Interface KeysMaintenance Troubleshooting Obtaining Factory Service Technical SupportIntroduction Model Number 5X00/A-12 Scanner IdentificationConnecting the Scanner Cable, Keyboard, and Terminal will varyScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PS/2 and Compatibles Interface IBM PC AT and Compatibles Interface DefaultIBM PC, Wand Emulation Interface IBM PC XT and Compatibles InterfaceIBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Instructions Dual Interface Programming NotesRS-232 Selection Code 39 Wand Emulation SelectionSame Code Wand Emulation Selection Laser Emulation SelectionDual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix SelectionPrefix and Suffix Examples Example 1 Add Suffix for Specific SymbologyExample 2 Add Suffix for ALL Symbologies Example 4 To Clear a Specific Prefix EntrySymbology Code Hex ValueBeeper Volume Selection Output Delays SelectionReread Delay Selection Good Read Delay SelectionLaser Voting Selection AIM I.D. Transmit Selection Buffered Scans SelectionCode I.D. Transmit Selection Function Code Transmit SelectionCTS Check Selection Baud Rate SelectionRS-232 Word Length Selection Parity SelectionProtocol Selection Serial Wedge Output Selection➌ Code I.D ➎ Editor Command Sequences➋ Terminal Type ➍ LengthRequire Data Format Data Format EditorSearch Commands Send CommandsMove Commands Miscellaneous CommandsData Formatter Example UPC a with 5 digit addendaScanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger SelectionTransmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad SelectionKeyboard Style Selections Keyboard StyleKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message LengthCheck Character Code 39 Selection AppendMinimum Maximum Full Ascii Chart Code 93 SelectionInterleaved 2 of 5 Selection Check DigitCode 2 of 5 Selection Matrix 2 of 5 SelectionCode 11 Selection Code 128 SelectionCode 128 Function Character Selection Code 16K Selection Code 49 SelectionEAN Selection IsbnUPC Selection UPC E1EAN Addenda Selection UPC Addenda SelectionMSI Selection Plessey SelectionScanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s GuideClone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris IBM, Memorex TelexSupported Esprit 200 Ansi AsciiBull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D FemaleWand Emulation RS-232 Laser Output Maintenance Cleaning the Scan WindowReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, IncWelch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output SelectionsGeneral Operating Menu Defaults Keyboard SelectionsSymbology Menu Defaults Industrial Codabar SelectionsCode 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda SelectionsScanteam 5700 User’s Guide Page Page Page Matrix 2 EANInterleaved 2 Code 2