Hand Held Products 5700 manual Keyboard Style Selections

Page 48

Keyboard Style Selections

Keyboard Style

Note: The Keyboard Style Table below applies the SCANTEAM 5700 software prior to software revision level 2.0.

This programming selection allows you to program the scanner to support special keyboard features, such as CAPS LOCK, SHIFT LOCK, Data Entry, and CTRL+ codes. These special keyboard features are shown in the chart below. Default = Style A.

Keyboard Style

(If terminal is not listed, then no secondary type keyboard is supported.)

Terminal	Style A	Style B	Style C	Style D	Style E
IBM PC/XT	XT	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

IBM PC/AT	AT	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

IBM PS2 (50–80)	NORM	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

HDS 2000, 3200	T/W	“CTRL +”

IBM 3180 (122 Key)	T/W	D/E

COMTERM 6178	T/W	D/E

TELEX (88 Key)	T/W	D/E

SIEMENS 9758	NORM	CAPS LOCK

NCR 7052	34Key	56 Key	122 Key Caps On	122 Key Caps Off

DEC	Norm	“CTRL +”	MAKE / BREAK

[ASCII function codes (00–1F) are sent to the terminal via a “CTRL+” sequence (i.e., ‘CR’=CTRL+M)

✱Style A

Style B

Style C

Style D

Style E

3–6	SCANTEAM 5700 User’s Guide

Image 48

Contents Decoded Output Disclaimer Scanteam 5700 User’s Guide FCC Class B Compliance StatementCanadian Notice A. StatementPatents Table of Contents Protocol Selection Serial Wedge Output Selection Require Data Format Data Format EditorMarker Beam Selection AutoTrigger Selection Foreign Keyboard SelectionIndustrial Symbology Selections Keyboard Function Relationships Supported Interface KeysMaintenance Troubleshooting Obtaining Factory Service Technical SupportIntroduction Model Number 5X00/A-12 Scanner IdentificationConnecting the Scanner Cable, Keyboard, and Terminal will varyScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC AT and Compatibles Interface Default IBM PC, Wand Emulation InterfaceIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles InterfaceIBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Instructions Dual Interface Programming NotesCode 39 Wand Emulation Selection Same Code Wand Emulation SelectionRS-232 Selection Laser Emulation SelectionDual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix SelectionExample 1 Add Suffix for Specific Symbology Example 2 Add Suffix for ALL SymbologiesPrefix and Suffix Examples Example 4 To Clear a Specific Prefix EntrySymbology Code Hex ValueBeeper Volume Selection Output Delays SelectionReread Delay Selection Good Read Delay SelectionLaser Voting Selection Buffered Scans Selection Code I.D. Transmit SelectionAIM I.D. Transmit Selection Function Code Transmit SelectionCTS Check Selection Baud Rate SelectionRS-232 Word Length Selection Parity SelectionProtocol Selection Serial Wedge Output Selection➎ Editor Command Sequences ➋ Terminal Type➌ Code I.D ➍ LengthRequire Data Format Data Format EditorSend Commands Move CommandsSearch Commands Miscellaneous CommandsData Formatter Example UPC a with 5 digit addendaScanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger SelectionTransmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad SelectionKeyboard Style Selections Keyboard StyleKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message LengthCheck Character Code 39 Selection AppendMinimum Maximum Full Ascii Chart Code 93 SelectionInterleaved 2 of 5 Selection Check DigitCode 2 of 5 Selection Matrix 2 of 5 SelectionCode 11 Selection Code 128 SelectionCode 128 Function Character Selection Code 16K Selection Code 49 SelectionEAN Selection IsbnUPC Selection UPC E1EAN Addenda Selection UPC Addenda SelectionMSI Selection Plessey SelectionScanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s GuideClone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris IBM, Memorex TelexSupported Esprit 200 Ansi AsciiBull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D FemaleWand Emulation RS-232 Laser Output Maintenance Cleaning the Scan WindowReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, IncWelch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output SelectionsGeneral Operating Menu Defaults Keyboard SelectionsSymbology Menu Defaults Industrial Codabar SelectionsCode 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda SelectionsScanteam 5700 User’s Guide Page Page Page EAN Interleaved 2Matrix 2 Code 2