Hand Held Products 5700 Dual Interface Programming Instructions, Dual Interface Programming Notes

Page 22

Scanner models 5700–X1 and 5700/X–X2 support the dual interface option allowing you to connect to two different terminals by switching interface cables. This option supports interfaces common to portable data terminals.

Dual Interface Programming Instructions

To program the scanner for secondary interface, follow the steps below. (Dual

Interface single scan programming codes are shown on the following pages.)

➊While the scanner is connected to the primary terminal interface, scan one of the single bar codes on 1–15 to enable the secondary interface.

➋Disconnect the primary interface cable from the scanner and attach the secondary interface cable.

➌Attach the secondary interface cable to the secondary terminal and power up the terminal.

➍Program the desired programmable selections for the secondary interface.

Dual Interface Programming Notes:

•To change the secondary interface from one selection to another (e.g., from HHLC to RS-232), the scanner must be reconnected to the primary interface, and then reprogrammed for the new secondary interface. Connect the scanner to the primary interface cable. Follow steps 1–4 above.

•Scanning “Plug and Play” bar codes (single scan terminal selection bar codes), or changing the terminal type does not affect Dual Interface settings.

•RS-232 programmable selections are used by both the primary and secondary interfaces. Changing an RS-232 parameter (e.g., baud rate or parity), while in primary or secondary mode will affect both interfaces.

•The Switch Power feature is a low power sleep mode which is automatically enabled when the secondary interface cable is attached and the unit is programmed for a second interface. The option is enabled when the unit is shipped.

Note: Dual Interface selection is not available if the scanner is programmed for an HP terminal with a Terminal I.D. of 20 or 79, or for a WYSE terminal with a Terminal I.D. of 13–18.

[Note: Section 2 contains information about Dual Interface Prefix/Suffix programming.

1–14	SCANTEAM 5700 User’s Guide

Image 22

Contents Decoded Output Disclaimer Canadian Notice Scanteam 5700 User’s GuideFCC Class B Compliance Statement A. StatementPatents Table of Contents Marker Beam Selection AutoTrigger Selection Protocol Selection Serial Wedge Output SelectionRequire Data Format Data Format Editor Foreign Keyboard SelectionIndustrial Symbology Selections Keyboard Function Relationships Supported Interface KeysMaintenance Troubleshooting Obtaining Factory Service Technical SupportIntroduction Model Number 5X00/A-12 Scanner IdentificationConnecting the Scanner Cable, Keyboard, and Terminal will varyScanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PS/2 and Compatibles Interface IBM PC AT and Compatibles Interface DefaultIBM PC, Wand Emulation Interface IBM PC XT and Compatibles InterfaceCode EAN IBM 4683 InterfaceCode Ocia Interface OCR, RS232 Interface Program Terminal Interface Supported TerminalsTerminal Models Terminal I.D ICL Status Check Reset Factory SettingsQuick Suffix Selections Dual Interface Programming Instructions Dual Interface Programming NotesRS-232 Selection Code 39 Wand Emulation SelectionSame Code Wand Emulation Selection Laser Emulation SelectionSwitched Power Mode Selections Dual Interface Enable/Disable SelectionLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Suffix Selection Primary Interface Prefix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix SelectionPrefix and Suffix Examples Example 1 Add Suffix for Specific SymbologyExample 2 Add Suffix for ALL Symbologies Example 4 To Clear a Specific Prefix EntrySymbology Code Hex ValueBeeper Volume Selection Output Delays SelectionGood Read Delay Selection Reread Delay SelectionLaser Voting Selection AIM I.D. Transmit Selection Buffered Scans SelectionCode I.D. Transmit Selection Function Code Transmit SelectionCTS Check Selection Baud Rate SelectionRS-232 Word Length Selection Parity SelectionProtocol Selection Serial Wedge Output Selection➌ Code I.D ➎ Editor Command Sequences➋ Terminal Type ➍ LengthRequire Data Format Data Format EditorSearch Commands Send CommandsMove Commands Miscellaneous CommandsData Formatter Example UPC a with 5 digit addendaScanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger SelectionWake Up Pulse Selection Transmission Rate SelectionOutput Polarity Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad SelectionKeyboard Style Selections Keyboard StyleKeyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message LengthCheck Character Code 39 Selection AppendMinimum Maximum Full Ascii Chart Code 93 SelectionInterleaved 2 of 5 Selection Check DigitCode 2 of 5 Selection Matrix 2 of 5 SelectionCode 11 Selection Code 128 SelectionCode 128 Function Character Selection Code 16K Selection Code 49 SelectionEAN Selection IsbnUPC Selection UPC E1EAN Addenda Selection UPC Addenda SelectionMSI Selection Plessey SelectionScanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s GuideClone Master Clone Destination+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Function Code HEX/ASCII Value Full Ascii Ctrl + Keyboard Function RelationshipsCountry Codes PS/2 Compatibles, IBM XTs Memorex Telex IBM AT/XTCompatibles Harris IBM, Memorex TelexSupported Esprit 200 Ansi AsciiHoneywell Bull BDS-7 Wyse WY-60/150HDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D FemaleWand Emulation RS-232 Laser Output Maintenance Cleaning the Scan WindowReplacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, IncNorth America Welch AllynEurope Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output SelectionsGeneral Operating Menu Defaults Keyboard SelectionsSymbology Menu Defaults Industrial Codabar SelectionsCode 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda SelectionsScanteam 5700 User’s Guide Page Page Page Matrix 2 EANInterleaved 2 Code 2