FujiFilm MP-300 owner manual Troubleshooting infrared communication problems

Page 23

Troubleshooting

Problems	Possible Causes	Solutions

The sending device	1 You left the printer	1 Press the POWER
sent the image, but	on for some time	button to turn the
it won’t	without using it at	printer back on.
communicate with	all (3 minutes when
the printer (also, the	using batteries and
POWER button is	10 minutes when
not lit).	using the AC power
	adapter).
	2 The film counter	2 Remove the photo
	shows “0”.	pack and load a new
		pack. (P.34)

Data transfer ended	1 No photo pack is	1 Load a new photo
and nothing was	loaded.	pack. (P.22)
printed.	2 A used photo pack	2 Load a new photo
	was loaded by	pack. (P.22)
	mistake.
	3 The image or text	3 Send a printable
	data sent is not	image format. (P.33)
	compatible with the
	printer.

The ERROR lamp	The ambient air	Use your body heat
blinked (for about 7	temperature is either	to warm the printer
seconds) and then	very low or very high	or place it in a cool
the printer turned	and the printer became	location. Once the
off.	too cold or too hot	printer’s temperature is
	(outside the printer’s	back inside its operating
	operating range of 5°C	range, the error will clear
	to 40°C (+41°F to +104°	and the printer will be
	F)).	ready to use. (P.41)

■Troubleshooting infrared communication problems

Problems	Possible Causes	Solutions

Data was sent from	1 The sending device	1 Send the data from a
your mobile phone	is not compatible with	compatible device.
but it can’t contact	the printer.
the printer (The	2 The infrared port on	2 Check the location of
POWER button does	the sending device	the infrared port on
not blink).	is not pointed at the	the sending device
	infrared port on the	and then send the
	printer.	data again from
		within the effective
		image transmission
		range. (P.27)
	3 Communication	3 Check the image
	was prevented by	transfer conditions
	a problem with the	and try again. (P.24)
	angle, distance or
	intervening obstacles.
	4 There is a problem	4 Try turning the printer
	with the infrared	off and on again.
	communication.

The POWER button	1 Communication with	1 Check the image
changed from	the sending device	transfer conditions
blinking to lit during	timed out (due to	and try again. (P.24)
data transfer and	a problem with the
nothing was printed.	angle, distance
	or intervening
	obstacles).
	2 Data transfer	2 Try again in a location
	was affected by	away from other
	interference from	infrared devices.
	another appliance or
	signals from another
	infrared device (TV or
	video remote, etc.).

44				45

Image 23

Contents Getting Ready Printing Advanced Printing Error Easy printing of beautiful prints FeaturesContents Quick Start Guide PictBridge Quick Start Guide Infrared communicationAbout IrSimple IntroductionUnstable substances which can give off dangerous vapors Safety PrecautionsDisconnect the AC power adapter Never get this product wet or handle it C with wet hands Handling & CarePrinter care Never attempt to take this product X apartHandling & Care Using USB interfaceUsing the AC power adapter Photo pack and print careDo not put in the mouth. Do not cut Do not pull apart RestrictionsFinishing prints Batteries Optional AC Power AdapterAC power adapter AC-5VX sold separately P.14 Necessary ItemsGetting Ready to Print Open the battery cover Loading the batteriesClose the battery cover Part NamesClose the photo pack door Loading the photo packPhoto pack conﬁrmation window Open the photo pack doorPrinting Setting up for infrared transmissionsPrinting Infrared communication Recommended image sizes for transmission Sending images from a camera phoneSelect the image on the mobile phone Select infrared transmissionPrinting PictBridge Setting up for USB transmissionsSelect PictBridge in the digital camera’s USB setting Take the film out when film output endsPress the Reprint button When all the specified imagesIf 2 or more prints are set at the camera Turn the printer offPrintable image sizes and formats Supported print SpecificationsAdditional Information and Notes on Printing PictBridge print speciﬁcation compatibility tableRemove the photo pack When the Film Runs OutWhen the ﬁlm runs out while printing Check that the film counter showsCheck that the printer is turned off Erasing the stored imageCheck that the printer is turned on Press the Date button Sharpen Mode Date ModePress the Sharpen button Blinking 3 times Error Error lampWhen PictBridge is used Date printing positionLit Error LOW Battery lampTroubleshooting Troubleshooting printer problemsTroubleshooting Troubleshooting infrared communication problemsTroubleshooting USB communication problems Glossary Troubleshooting problems with finished printsJpeg SpeciﬁcationAbout Mobile Printing Ready Products Speciﬁcation