Datamax E-4304 manual Connecting the Printer, Power Connection

Page 17

3.0Introduction

This chapter explains how to connect your printer, load media and ribbon (optional), and print a configuration label.

3.1 Connecting the Printer

3.1.1 Power Connection

The printer is powered from an external power supply that connects to the printer as shown below. Several power supplies are available depending on your printer model.

	Model	DPI	Print	Media Roll	Power Supply*
	Model	DPI	Speed	Diameter	Power Supply*
			Speed	Diameter
	E-2303	203	3 IPS	4”	Standard (Non Auto-Ranging)
					110V: 50-2024-01
					220V: 50-2034-01
	E-4203 with	203	4 IPS	4”	Standard (Auto-Ranging)
	4 IPS Option				50-2050-01
	E-4204	203	4 IPS	5”	Standard (Auto-Ranging)
					50-2050-01
	E-4304	300	4 IPS	5”	Standard (Auto-Ranging)
					50-2050-01

*The optional Heavy Duty Power Supply (50-2049-01) can be used for high demand applications with any of the above printer models.

Ensure that the power supply shipped with your printer is compatible with your electrical service.

E-4203/E-4204/E-4304

7

Image 17

Contents 4203 / E-4204 / E-4304 Page Part Number Firmware Software AgreementAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Label Alignment Troubleshooting Troubleshooting Page Direct Thermal Model IntroductionAbout this Printer Standard FeaturesThermal Transfer Optional Features4203/E-4204/E-4304 Removing the Packaging Before using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionLoading Media Loading Media for Peel Configuration Loading Ribbon Thermal Transfer 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Front Panel OperationButtons Normal Mode Button FunctionsPrinter Setup Mode Button Functions Printer Setup Menu List Media Type Sensor Type Menu Items and ValuesRange 0 15 default = *10 Internal Module Example of Changing Baud Rate 4203/E-4204/E-4304 New ‘19.2’ Value Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoLabel Stock Label Alignment Setting Label Alignment Recommended SettingsProblem Possible Solution Description Label Alignment TroubleshootingProblem Possible Solution Description Cause Fault LED Calibration Mode Media Sensor Calibration Procedure Auto Media Calibration Procedure Internal Labels Database Configuration and Dot Check LabelGood Test Label Faulty Test LabelTo print the Test Label Test Label4203/E-4204/E-4304 Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Ribbon Width Direction of Rotation Ribbon Width AdjustmentFine Printhead Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Problem Situation Unacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical Printer SpecificationsPrinter Specifications Flash Memory Communications Media/RibbonFonts Imbedded Bar CodesDesignator Description Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Alphanumeric, uppercase Page Bar Code Type Length Check Valid Ascii Characters BarcodesUPS Barcode H Health Industry Barcode O Code Barcode p Postnet Barcode I CodabarBarcode K Plessey Kmart NON EDI Bar Code W1f Aztec Barcode T TelepenBarcode v FIM Bar Code W1c DataMatrix Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304