Datamax E-4304 manual Ups

Page 72

Bar Code		Type				Length	Check-	Valid ASCII Characters,
ID							sum	decimal value
								representation
u	UPS	MaxiCode			with	Specified	Yes	Alphanumeric
	Byte Count
v	FIM					1	No	A, B, C, D
z	PDF417					Varies	Yes	All
Z	PDF417 with				Byte	Specified	Yes	All
	Count
W1c	DataMatrix					Varies	Yes	All 8-bit values
W1C	DataMatrix		with Byte			Specified	Yes	All 8-bit values
	Count
W1d	QR	Code	–		Auto	Varies	Yes	Alphanumeric
	format
W1D	QR Code		–	Manual		Varies	Yes	Single-byte or Kanji double-
	format							byte
W1f	Aztec					Varies	Yes	All 8-bit values
W1F	Aztec	with			Byte	Specified	Yes	All 8-bit values
	Count
W1T	TCIF			Linked		Varies	No	Alphanumeric
	Barcode		3	of 9
	(TLC39)
W1z	MicroPDF417					Varies	Yes	All 8-bit values
W1Z	MicroPDF417				with	Specified	Yes	All 8-bit values
	Byte Count

B-6	E-4203/E-4204/E-4304

Image 72

Contents 4203 / E-4204 / E-4304 Page Firmware Software Agreement Part NumberAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Label Alignment Troubleshooting Troubleshooting Page Introduction Direct Thermal ModelStandard Features About this PrinterOptional Features Thermal Transfer4203/E-4204/E-4304 Before using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesLoading Media Loading Media for Peel Configuration Loading Ribbon Thermal Transfer 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Front Panel Operation LightsNormal Mode Button Functions ButtonsPrinter Setup Mode Button Functions Printer Setup Menu List Menu Items and Values Media Type Sensor TypeRange 0 15 default = *10 Internal Module Example of Changing Baud Rate 4203/E-4204/E-4304 New ‘19.2’ Value Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Recommended Settings Label Stock Label Alignment SettingLabel Alignment Troubleshooting Problem Possible Solution DescriptionProblem Possible Solution Description Cause Fault LED Calibration Mode Media Sensor Calibration Procedure Auto Media Calibration Procedure Database Configuration and Dot Check Label Internal LabelsFaulty Test Label Good Test LabelTest Label To print the Test Label4203/E-4204/E-4304 Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Ribbon Ribbon Width Direction of RotationFine Printhead Adjustment Printhead Replacement RemovalDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Problem Situation Unacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printer Specifications Printer SpecificationsMechanical Flash Memory Media/Ribbon CommunicationsFonts Imbedded Bar CodesApproved Media Designator Description4203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Alphanumeric, uppercase Page Barcodes Bar Code Type Length Check Valid Ascii CharactersUPS Barcode H Health Industry Barcode I Codabar Barcode K PlesseyBarcode O Code Barcode p Postnet Kmart NON EDI Barcode T Telepen Barcode v FIM Bar Code W1c DataMatrixBar Code W1f Aztec Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304