Datamax E-4304 manual Example of Changing Baud Rate

Page 32

4.4.3 Example of Changing Baud Rate

The following is a step by step example for modifying the Printer Setup. Although this example will show how to modify only the Baud Rate value from a default of 9600 bps to 19200 bps the same procedure can be used to change any of the printer’s menu items.

Note: It is recommend that the Printer Setup Mode is not executed with the printer in Peel Mode or the optional Present Sensor enabled. Depending on label size this can cause unpredictable results.

1.With printer off and properly loaded with media press and hold the button while powering up the printer. Continue to hold the button until the PAUSED light turns off then release.

2.Press and hold the button and count 7 flashes of the FAULT light then release. The following printout should be showing:

3.Press the button once to increment to the 19200 bps value. The following printout should be showing:

4.At this point you will accept the current values for “test” and exit the Printer Setup Procedure by pressing the + buttons simultaneously.

Note: If you wish to discard your changes and revert back to the previous values simply turn off the printer before Step 5.

5.Now you can save your changes and resume by again pressing the + buttons simultaneously. Wait about 15 seconds

for to begin.

22

E-4203/E-4204/E-4304

Image 32
Contents 4203 / E-4204 / E-4304 Page Firmware Software Agreement Part NumberAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Label Alignment Troubleshooting Troubleshooting Page Introduction Direct Thermal ModelStandard Features About this PrinterOptional Features Thermal Transfer4203/E-4204/E-4304 Before using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesLoading Media Loading Media for Peel Configuration Loading Ribbon Thermal Transfer 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Front Panel Operation LightsNormal Mode Button Functions ButtonsPrinter Setup Mode Button Functions Printer Setup Menu List Menu Items and Values Media Type Sensor TypeRange 0 15 default = *10 Internal Module Example of Changing Baud Rate 4203/E-4204/E-4304 New ‘19.2’ Value Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Recommended Settings Label Stock Label Alignment SettingLabel Alignment Troubleshooting Problem Possible Solution DescriptionProblem Possible Solution Description Cause Fault LED Calibration Mode Media Sensor Calibration Procedure Auto Media Calibration Procedure Database Configuration and Dot Check Label Internal LabelsFaulty Test Label Good Test LabelTest Label To print the Test Label4203/E-4204/E-4304 Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Ribbon Ribbon Width Direction of RotationFine Printhead Adjustment Printhead Replacement RemovalDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Problem Situation Unacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Mechanical Printer SpecificationsPrinter Specifications Flash Memory Media/Ribbon CommunicationsFonts Imbedded Bar CodesApproved Media Designator Description4203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Alphanumeric, uppercase Page Barcodes Bar Code Type Length Check Valid Ascii CharactersUPS Barcode H Health Industry Barcode O Code Barcode p Postnet Barcode I CodabarBarcode K Plessey Kmart NON EDI Bar Code W1f Aztec Barcode T TelepenBarcode v FIM Bar Code W1c DataMatrix Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304