Datamax E-4304 manual New ‘19.2’ Value

Page 34

6.To confirm that your changes have been made press the + buttons simultaneously, this will print the Database Configuration Label. The label should show the new Baud Rate value of 19200.

FRI AUGUST 024, 2001 19:29 236 VER: ET4204 - 04.06 08/24/01 BOOT 83-2329-04A

CODE 83-2325-04F

FONT 83-2337-01A

CPLD 592157-01C

INTERNAL FLASH MODULE PRESENT SYSTEM RAM CHECKS____ GOOD

SYSTEM RAM SIZE___ 2015 KBYTES SYSTEM RAM AVAIL__ 1244 KBYTES REG POWER SUPPLY__ YES

INPUT VALUES

PAPER_____________ 255

DARKNESS__________ 131

TRAN______________ 255

REFL______________ 149

RIBN______________ 87

TEMP______________ 48

VOLT______________ 223

CONFIGURATION

DIRECT THERMAL SERIAL PORT SELECTED 19.2; 8BITS

EDGE
CONT FORM LENGTH__	0
PRESENT ADJUST____	127
SOP ADJUST________	127
TOF LOW___________	0	0
TOF DELTA_________	10	10
TOF GAIN__________	12	10
OOS MAXVOLT_______	3	3
LABEL ALIGNMENT___	NO
ALIGN LENGTH______	100

STOP LOCATION_____ HOST

COUNTER INFORMATION ABSOLUTE VALUES 6-18-2001

LENGTH____	773	INCHES
TIME______	20	HOURS
RESETTABLE VALUES 6-22-2001
LENGTH____	576	INCHES
TIME______	10	HOURS
MEMORY CONFIGURATION
INTERNAL MODULE______			15
SCALABLE FONTS_______			32
LABEL SIZE	0416:02157 IN

New ‘19.2’

Value

24	E-4203/E-4204/E-4304

Image 34

Contents 4203 / E-4204 / E-4304 Page Firmware Software Agreement Part NumberAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Label Alignment Troubleshooting Troubleshooting Page Introduction Direct Thermal ModelStandard Features About this PrinterOptional Features Thermal Transfer4203/E-4204/E-4304 Before using the Printer Removing the PackagingInspecting the Printer Additional RequirementsConnecting the Printer Power ConnectionInterface Connection Interface CablesLoading Media Loading Media for Peel Configuration Loading Ribbon Thermal Transfer 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Front Panel Operation LightsNormal Mode Button Functions ButtonsPrinter Setup Mode Button Functions Printer Setup Menu List Menu Items and Values Media Type Sensor TypeRange 0 15 default = *10 Internal Module Example of Changing Baud Rate 4203/E-4204/E-4304 New ‘19.2’ Value Label Alignment Label Alignment = YESLabel Alignment = Auto Label Alignment = noLabel Alignment Recommended Settings Label Stock Label Alignment SettingLabel Alignment Troubleshooting Problem Possible Solution DescriptionProblem Possible Solution Description Cause Fault LED Calibration Mode Media Sensor Calibration Procedure Auto Media Calibration Procedure Database Configuration and Dot Check Label Internal LabelsFaulty Test Label Good Test LabelTest Label To print the Test Label4203/E-4204/E-4304 Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Width Adjustment Ribbon Ribbon Width Direction of RotationFine Printhead Adjustment Printhead Replacement RemovalDarkness Adjustment Resetting to the Factory DefaultsDownloading Firmware and Fonts Problem Situation Unacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printer Specifications Printer SpecificationsMechanical Flash Memory Fonts Media/RibbonCommunications Imbedded Bar CodesApproved Media Designator Description4203/E-4204/E-4304 Ascii Control Code Chart XON Embedded Fonts and Barcodes Font Valid Ascii Characters decimal Use with RecordAlphanumeric, upper and lower Alphanumeric, uppercase Page Barcodes Bar Code Type Length Check Valid Ascii CharactersUPS Barcode H Health Industry Barcode K Plessey Barcode I CodabarBarcode O Code Barcode p Postnet Kmart NON EDI Barcode v FIM Bar Code W1c DataMatrix Barcode T TelepenBar Code W1f Aztec Datamax Barcode Products Limited Warranty Statement PrinterWarranty Service Procedures Thermal PrintheadGeneral Warranty Provisions Limitation of Liability4203/E-4204/E-4304