Datamax E-4304 manual Internal Module

Page 31

17) INTERNAL MODULE

18) LABEL ALIGNMENT (see section

Sets the number of 4K Byte blocks

4.5 for more information)

Sets Label Alignment Method.

allocated for the internal RAM

module.

Possible Values:

 

Possible Values:

YES

(printer uses ‘ALIGNMENT

 

0 – 255; default = *128

AUTO

LENGTH’ or host sent value)

 

(printer will automatically

 

 

determine label length)

 

* NO

(Label Alignment disabled)

 

 

19) ALIGNMENT LENGTH (see

20) STOP LOCATION

section 4.5 for more information)

Sets convenient stop locations for

Leading edge to leading edge

different printer configurations.

distance of two successive labels.

Possible Values:

Must be set when ‘LABEL

ALIGNMENT’ is set to Yes.

*HOST

(printer uses host values of SOP

 

Possible Values:

 

and Present Distance)

PEEL

(sets stop location just behind the

 

0 – 999; default =100*

 

peel bar)

Units: .01 inch

CUT

(sets stop location at the cutter

 

 

blade)

 

COVER (sets stop location at the tear plate)

 

NONE

(printer uses normal start location

 

 

and ignores host commands)

*= Default Setting

All of the menu items listed in the previous tables are stored in non-volatile memory.

E-4203/E-4204/E-4304

21

Page 30 Page 32
Image 31
Page 30 Page 32
Contents 4203 / E-4204 / E-4304 Page Part Number Firmware Software AgreementAgency Compliance and Approvals Important Safety Instructions Page Printer Overview Label Alignment Troubleshooting Troubleshooting Page Direct Thermal Model IntroductionAbout this Printer Standard FeaturesThermal Transfer Optional Features4203/E-4204/E-4304 Removing the Packaging Before using the PrinterAdditional Requirements Inspecting the PrinterPower Connection Connecting the PrinterInterface Cables Interface ConnectionLoading Media Loading Media for Peel Configuration Loading Ribbon Thermal Transfer 4203/E-4204/E-4304 Flash Memory Expansion 4203/E-4204/E-4304 Lights Front Panel OperationButtons Normal Mode Button FunctionsPrinter Setup Mode Button Functions Printer Setup Menu List Media Type Sensor Type Menu Items and ValuesRange 0 15 default = *10 Internal Module Example of Changing Baud Rate 4203/E-4204/E-4304 New ‘19.2’ Value Label Alignment = YES Label AlignmentLabel Alignment = no Label Alignment = AutoLabel Stock Label Alignment Setting Label Alignment Recommended SettingsProblem Possible Solution Description Label Alignment TroubleshootingProblem Possible Solution Description Cause Fault LED Calibration Mode Media Sensor Calibration Procedure Auto Media Calibration Procedure Internal Labels Database Configuration and Dot Check LabelGood Test Label Faulty Test LabelTo print the Test Label Test Label4203/E-4204/E-4304 Area Method Interval Cleaning the Printhead Media Width Adjustment Ribbon Ribbon Width Direction of Rotation Ribbon Width AdjustmentFine Printhead Adjustment Removal Printhead ReplacementResetting to the Factory Defaults Darkness AdjustmentDownloading Firmware and Fonts Problem Situation Unacceptable print quality Skips every other label Label advances 1-2 inches before a fault indication Printer Specifications Printer SpecificationsMechanical Flash Memory Imbedded Bar Codes Media/RibbonCommunications FontsDesignator Description Approved Media4203/E-4204/E-4304 Ascii Control Code Chart XON Font Valid Ascii Characters decimal Use with Record Embedded Fonts and BarcodesAlphanumeric, upper and lower Alphanumeric, uppercase Page Bar Code Type Length Check Valid Ascii Characters BarcodesUPS Barcode H Health Industry Barcode K Plessey Barcode I CodabarBarcode O Code Barcode p Postnet Kmart NON EDI Barcode v FIM Bar Code W1c DataMatrix Barcode T TelepenBar Code W1f Aztec Printer Datamax Barcode Products Limited Warranty StatementThermal Printhead Warranty Service ProceduresLimitation of Liability General Warranty Provisions4203/E-4204/E-4304
Top Page Image Contents