Matsushita CF-Y5LWVYZ 1 2 service manual Assembly knowhow of the LCD, Assembly of the LCD Front

Page 35

9.3. Reassenbly instructions

9.3.1. Attention when CF-Y5L series is repaired

-Please execute writing BIOS ID when you exchange the main board.

-Parts (sheet and rubber) etc.related various the conductive cloth and heat spreader cannot be recycled.Use new parts.

9.3.2.Assembly knowhow of the LCD

9.3.2.1.Assembly of the LCD Front

LCD Rubber

LCD Rubber

LCD Front

Wide Narrow LCD Front

LCD Rubber

LCDBATTRubberer

Affixes in the standard on the left

Be parallel after putting

Safety Work

(Attention)

-The LCD Front is installed in the receiving stand, and works.

-The LCD rubber and LCD BATT Rubber does not out of the concave part, moreover, not run aground.

-It is noted that the finger does not touch the paste side when the LCD Rubber and LCD BATT Rubber are affixed.

9.3.2.2. Putting LCD Side Cushion / LCD Tape 1

0-2mm

Hinge Side

0-1mm

Hook Side

LCD Side Cushion 1

Hook central standard

Hook

0-1mm

There must not be floatage

Floatage NG

(Influences and exist in the hook intuition combination when float- ing)

There must not be beginning to

see from the frame on the inside

LCD Tape 1

Wall root applica- tion putting From wall root

0-1mm

From the frame on the inside 0.5-1.5mm

0-2mm

Hook Side

Hinge Side

There must not be floatage

LCD Side Cushion 1

Hook central standard

hook

Edge standard of

LCD Tape 1

wall of length 0

2mm

35

Image 35
Contents CF-Y5 For U.K This apparatus must be earthed for your safety How to replace the fuseLaser Safety Information Page Page Contents Secondary cache memory Specifications„ Main Specifications Bluetooth Wireless LANUseful Information Getting Started Names and Functions of Parts Headphone Jack SD Memory Card Slot Bluetooth AntennaBattery Latches Battery Pack Emergency Hole RAM Module Slot DC-IN Jack Ventilation Hole External Display PortYonah LV Dual Core Block DiagramDiagnosis Procedure Flow Chart TroubleshootingDiagnosis Power-On Self Test Boot CheckError Diagnosis by Checking Beep Signal Sound Outline of PostStuck key 02D0 System cache error Cache disabled Shift and left Shift keys When you execute an automatic testWhen you execute the enhancing test Self Diagnosis TestOperation of PC-Diagnostic Utility Selection of tested device PC-Diagnostic utility End methodContent of the setup is returned to the setting of the user Place with possibili EnhancingMemory as Vram may fail with Cable characteristic and deviceStandard Enhanced Breakdown. e.g.. Head, MotorLCD Wiring Connection DiagramDisassembly instructions Removing the Keyboard Before disassembly, be sure to perform the following stepsPreparation Removing the HDDPreparation perform the .2.1., 9.2.3. first Removing the Top CaseSUB DVD Removing the SUB DVDPreparation perform the .2.1., 9.2.3. and 9.2.4. first FfcpadffcswTop Case Screw Q Solenoid Line Hold Sheet Cable Fixed Sheet Removing the Touch Pad / LCD KnobRemoving the Solenoid / Disc Cover Lock Pad WP Sheet LCD Knob LCD Latch Spring Top CaseFAN Removing the Speaker L, RRemoving the FAN Preparation perform the .2.1 9.2.4. firstGadket Removing the Drive UnitRemoving the Main Board USB FPC Removing the DC-IN CableRemoving the Antenna Board Unit L, R Modem Removing the ModemPreparation perform the .2.1 9.2.11. first Preparation perform the .2.1 9.2.18. first Removing the LCD UnitRemoving the Hinge Cover L, R Removing the LCD Unit and the LCD RearCN2 Removing the LCD Cable / Inverter Board2mm Hinge Side 1mm Hook Side LCD Side Cushion Assembly knowhow of the LCDAssembly of the LCD Front Putting LCD Side Cushion / LCD TapeRib Rib standard Putting LCD Side Rubber / LCD Side DamperLCD Side RubberPutting LCD Magnet Putting LCD Cushion / Assembly of the InverterExternals match Putting Tape for LCD CablePreparation for Inverter Case OrderPage Page Putting Line Hold Sheet / Antenna Sheet / BT PWB Cushion Assembly knowhow of the Main BoardPutting MCH Sheet / Heat Spreader Bottom HDD FPC Assembly of the Wlan Sheet / MCH Thermal TapeAssembly of the Main Board Right before building Left before building Square hole Assembly of the Card Bus EjectorSafety work Assembly of the Wireless LAN Module / ModemDXQT2+D25FNL Insert the Main BoardDXQT2+E6FNL Assembly of the Disk Cover Assembly knowhow of the Top CaseLAN on /OFF Assembly of the Top CaseLan Sw Blank Installation Putting Disk Angle CushionSEC Assembly of the LCD Knob / Putting CushionTop Case Rib Case rib and folds to the rib sidePad Cover Externals Assembly of the Touch PadInstall the Pad Cover Safety workPad Cover installation position Cushion Putting SheetFixation seat Affixes Disk cover cushionAssembly of the Break Lever Conclusion Assembly of the FANAxis nor the shuttlecock Confirmation two places as Assembly of the Disk Cover ClickAssembly of the Disk Cover Lock / SW PCB Engagement fingernail isPossible to recycle SW PCB yellow line Screw DXHM0056ZA Yellow lineSW PCB Affixation Disk Lever Fix CushionAssembly of the Speaker Assembly of the SolenoidWiring Speaker Cable Difference line Putting Cushion / Tape / SheetAssembly of the SW PCB FFC Page Putting Line Hold Sheet Assembly knowhow of the Bottom CaseAssembly of the Dimm Cover LED Lenz SD Cutting lack part top side Do not go out of the rib FIG1 Safety WorkPutting Foot Rubber Main PWB Assy Assembly knowhow of the BodyInstallation of Main Board Keyboard preparationFIG2 Assembly of the HDD Slot GuardInsert the Modem Cable in the slit Putting Line Hold Sheet 3 / Line Hold CushionBack Side without tapeFFC ANT PWBCable black Tape Externals Installation of LCD UnitSide with I-PEX stamp Cable in CNCPU DFHE5035ZBAffixes Gasket Cloth FIG1 Assembly of the DVD DriveLAN ON/OFF Installation of Power Knob / LAN SW KnobAssembly of the Body DXQT2+E6FNL DXQT2+F3FNL DXQT2+E10FNL DRQT2+E8FKL Installation of K/B Heat SpreaderTop Case side screw tightening Installation of Keyboard Installation of Disk Cover / Disk Side CoverSide Cover L Installation of K/B Side CoverHow to detach Keyboard and K/B Side Cover Side Cover RBottom Case side screw tightening Installation of HDDDFQT0046ZA Putting LabelScrew tightening torque Exploded ViewK52 K145 K157 Cabinet SectionN7 Screw tightening torque REF. no and Area Replacement Parts ListDFHG1874YA LCD Cushion DFMD1202ZA DC Jack Plate DFHR3D21YA Line Hold Sheet DXQT2+E6FNL Screw EEFCX0D221R CF-Y5LWVYZBM 2006/11/16 REF. no and AreaEEFSX0D331ER EEFCD0D101ER ConnectorEEFCX0J101R EEFCX0G151RDEDRB081L20 Diode IC, Temperature Censor ICIC, USB Power SW DiodeIC, Power Management Switch IC, FET SwitchIC, Q-SWITCH IC, Audio Power AmplifierERJ2GEJ102X RESISTOR, 1/16W, 1KΩ B1GFCFEN0003 TransistorB1GBCFNN0042 Transistor B1GBCFNL0017 TransistorERJ2GE0R00X RESISTOR, 1/16W, 0Ω ERJ2GEJ103X RESISTOR, 1/16W, 10KΩERJ2GEJ201X ERJ2GEJ100XERJ2GEJ472X ERJ2GEJ105X RESISTOR, 1/16W, 1MΩERJ2RKF3922X ERJ2RKF2002X RESISTOR, 1/16W, 20KΩBluetooth Module Slide SwitchEVQPLDA15 Switch CONNECTOR, USBERJ2GE0R00X RESISTOR, 1/16W, 0Ω