Matsushita CF-19FHGAX service manual Self Diagnosis Test

Page 17

7 Self Diagnosis Test

As for the self-diagnosis test(PC-Diagnostic utility) to use this model, a standard test and the enhancing test by the module of the main body building in are possible.

●Notes To skip BIOS password

Use <Ctrl>+<F10> key to skip BIOS password or authentication of fingerprint. This key is only for entering DIAG mode. Not available to boot the computer. If customer set "HDD Lock", the DIAG program cannot perform HDD test.

*This key is for service purpose only. Do not disclose this information to unrelated others.

1.Beginning of self-diagnosis test 1-1. Setting of content of setup

1.The power supply of the computer is turned on.

2." F2 " is pushed on the screen of "Panasonic" while " press <F2 to enter Setup> " is displayed.

3.The setup utility starts and then takes notes of the content of the BIOS setup of present set.

4." F9 " is pushed, " Yes" is selected on the screen of " Is the default value loaded? ", and " Enter" is pushed.

5." F10 " is pushed.

6." Yes" is selected on the screen of the setup confirmation, and " Enter" is pushed.

7.The computer starts automatically.

Attention

If the device which can be set is set to "Invalidity" by "Advanced" or "Security" menu, becomes an error by "PC-Diagnostic utility".

(It is judged that the device which can be set to "Invalidity" by "Main" menu such as "Flat pad" is normal if the controller operates normally though sets to "Invalidity" by the setup. )

In the model with built-in DVD of the USB connection, even if DVD is normal, becomes an error if legacy USB is set to "Invalidity"

1-2. When you execute an automatic test

1."Ctrl" + "F7" is pushed while the "Panasonic" start screen is displayed after the computer is started.

2.The test of all devices begins automatically by "PC-Diagnostic utility" 's starting.

Attention

It is a test which the customer who bought PC can execute. (As for HDD, the enhancing test is also possible.)

A flat pad does not work for a while after starting "PC-Diagnostic utility".

The movement of a flat pad might become abnormal If after RAM begins from the CPU/System test, a flat pad will be operated in about 30 seconds. In that case,restarts pushing"Alt" + "Ctrl" + "Del" key. Or, please start "PC-Diagnostic utility" again after doing the power supply switch in the slide, and turning off the power supply.

1-3. When you execute the enhancing test

1.Please let me discontinue diagnosing clicking to end an automatic test.

2.Please click on the character of "D" "PC-Diagnostic utility" on the screen while pushing both of right "Shift" and left "Shift" keys.

3.All devices which can select the enhancing test make the setting of the enhancing test possible.

4.The district device is made"FULL" display (enhancing test).

5.The test begins clicking .

*Please refer to item 4 for the error result of each test and the division of the breakdown part.

17 / 90

Image 17
Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessHost PCI Bridge InternalSigmatel AC-linkDiagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lightingOutline of Post Error Diagnosis by Checking Beep Signal SoundTable of errors classified by beep sounds Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394Removing the Touch Pad and Key- board Removing the Battery Pack and HDD PackPreparation Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Audio PCB Removing the Hsdpa PCB and Bluetooth PCBRemoving the DU Lid Unit HDD Removing the left LED and right Removing the Power SW PCBRemoving the I/O PCB Assy Removing the Display unit Removing Pad PCB and SW PCBRemoving Inverter PCB and LCD Unit Removing the LCD Rear CaseRemoving the LCD Hinge USB Removing the Each CoverPCB Spacer Setting up the Inverter Assy and LCD UnitSheet Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeScrew LCD Hinge Assembly of LCD HingeCable Hold Plate S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking linesAntenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Putting of the TP Bottom Tape Setting the left LED PCB and right LED PCBAssembly of the Pad PCB and SW PCB Assembly of the Power SW PCB Setting the Power SW PCBAssembly of the left LED PCB and right LED PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm HolderScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable StepCable Process 3/3 Step Cable Holder CushionAssembling the DU Lid Unit Setting the Rear CabinetBottom Rubber Tape Bottom Case Assy Setting the Dimm Lid AssyDimm Thermal Sheet Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListMechanical Parts AccessoriesPacking Material DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller