Matsushita CF-19FHGAX service manual K51

Page 69

E35	H	N2
E35

K99

K98

K137K160

A N9

E3

A

N19

A N9

K1051

E27

A

A N19	K86	E26
A N19	E1
	E1
	A
	N19		E30
	K87	A	E30
		N19
		K88	E401 K54 K12949 K130

K141

E402	A N9

K38

K54

K47

N9

K142 A

N9

K46

E33

		A N9
A N9	E29	K91
		K131
K161	N19	E11
	N19	A N1
		A N1
	K93	K140
		K140

	K122
K121			K51
		E401	K51
E405		A N19
A N19		A N19
A N19
K95		E13	E2
K95		E13

A N19		K45		E12
A N19

				A N8
			K50	K95
E9			A N3	E28
			A N3
	E403
	E403
A N19	K48			K33
A N19		A N9		K33
K157		A N9			A	N1
			A		A	N1
					K132

			K37 N9				A
			K37 N9				A
E14				A N9			N1
E14				A N3
	A N4		E7	A N3
	A N4		E7
	K35				A N1
		A			A N1
		A
		N9	K15				A N1
							A N1
A N9		A N5	K53				A N1
A N9		A N5	K53				K165

AN5

K22E407

E4

K138	K94		A N9
	K94		A N9
E404		K96
K43			E10
			E10
	E20		A N9
	E20	A N19	A N19
		A N9 N19A	A N9
K126		K92
		K92

AN1

	A N1
	K43	E406	A N1
	K43	E409	E31
		E409	E31

K42

Screw tightening torque

A	0.2 + 0.02N	m
H	(2.0 + 0.2kgf		cm)
H	0.4 + 0.02N	m
A N1	(4.0 + 0.2kgf		cm)

CF-19FHGAXxM

69 / 90

Image 69

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessHost PCI Bridge InternalSigmatel AC-linkDiagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lightingError Diagnosis by Checking Beep Signal Sound Table of errors classified by beep soundsOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394Removing the Battery Pack and HDD Pack PreparationRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Hsdpa PCB and Bluetooth PCB Removing the DU Lid UnitRemoving the Audio PCB HDD Removing the Power SW PCB Removing the I/O PCB AssyRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCBRemoving the LCD Rear Case Removing the LCD HingeRemoving Inverter PCB and LCD Unit USB Removing the Each CoverSetting up the Inverter Assy and LCD Unit SheetPCB Spacer Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeAssembly of LCD Hinge Cable Hold PlateScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking linesAntenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Setting the left LED PCB and right LED PCB Assembly of the Pad PCB and SW PCBPutting of the TP Bottom Tape Setting the Power SW PCB Assembly of the left LED PCB and right LED PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm HolderScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable StepCable Process 3/3 Step Cable Holder CushionAssembling the DU Lid Unit Setting the Rear CabinetSetting the Dimm Lid Assy Dimm Thermal SheetBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListAccessories Packing MaterialMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller