Matsushita CF-19FHGAX service manual Assembly of Main Unit

Page 53

■Assembly of Main Unit

Audio FPC Ass'y
Audio FPC Stiffening Plate Side
Lengthwise
Attach it on the
center of the
FPC.
3mm
Tape	Fold back

0	1mm

Audio FPC Ass'y

Insert it before setting the Main Board.

Screw

Apply the lubricant (sub material) on the HDD Connector for about 1 second. (Note for spraying around when applying.)

Round to make the brown side outside and insert the notch.

Screw Insert and then lock.		Connect
		Connect
DU PCB ASSY
		Screw
Screw	Screw
Screw		Screw
Screw
Thermal Sheet	Screw
Thermal Sheet	S4
Center of module	S4
to the notch
Wireless Module		Screw
	Screw

Safety critical componentInsert and then lock.

Important Parts

for Safety

Main PCB Ass'y

Safety Working

Insert and then lock

CAUTION

S1:Insulation S2:Pinching Cables S3:Sharp Edge S4:Part No. Check S5:Others

53 / 90

Image 53

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessHost PCI Bridge InternalSigmatel AC-linkDiagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lightingOutline of Post Error Diagnosis by Checking Beep Signal SoundTable of errors classified by beep sounds Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394Removing the Touch Pad and Key- board Removing the Battery Pack and HDD PackPreparation Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Audio PCB Removing the Hsdpa PCB and Bluetooth PCBRemoving the DU Lid Unit HDD Removing the left LED and right Removing the Power SW PCBRemoving the I/O PCB Assy Removing the Display unit Removing Pad PCB and SW PCBRemoving Inverter PCB and LCD Unit Removing the LCD Rear CaseRemoving the LCD Hinge USB Removing the Each CoverPCB Spacer Setting up the Inverter Assy and LCD UnitSheet Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeScrew LCD Hinge Assembly of LCD HingeCable Hold Plate S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking linesAntenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Putting of the TP Bottom Tape Setting the left LED PCB and right LED PCBAssembly of the Pad PCB and SW PCB Assembly of the Power SW PCB Setting the Power SW PCBAssembly of the left LED PCB and right LED PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm HolderScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable StepCable Process 3/3 Step Cable Holder CushionAssembling the DU Lid Unit Setting the Rear CabinetBottom Rubber Tape Bottom Case Assy Setting the Dimm Lid AssyDimm Thermal Sheet Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListMechanical Parts AccessoriesPacking Material DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller