Matsushita CF-19FHGAX service manual Setting the Touch Pad and Keyboard

Page 61

9.2.17. Setting the Touch Pad and Keyboard

1.Connect the Cable to the Connector (CN800), and attach the Touch Pad to the computer.

2.Set the Click Button Plate.

3.Attach the new TP Tape over the Touch Pad.

4.Attach the Palm Rest Ass'y on the computer.

7. Set the Keyboard to the computer.

Keyboard

Keyboard

FPC

TP Tape

Touch Pad

Click Button

Plate

	Connector	Connector
	(CN800)
		(CN18)

5.Connect the Cable of the Keyboard to the Connector (CN18) on the Main PCB.

6.Fix the KBD Connector Cover using the three Screws. <N1>

1

2

Keyboard

8. Fix the KBD Plate using the four Screws. <N9>

KBD Plate

	<N9>
	<N9>	KBD Plate
		KBD Plate
Palm Rest Ass'y		<N9>
Palm Rest Ass'y		<N9>
		<N9>

<N1>

Screws <N1> : DFHE5025XA

Screws <N9> : DRSB2+5FKL

KBD

Connector

Cover

61 / 90

Image 61

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessHost PCI Bridge InternalSigmatel AC-linkDiagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lightingTable of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCBRemoving the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit USB Removing the Each CoverSheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeCable Hold Plate Assembly of LCD HingeScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking linesAntenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm HolderScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable StepCable Process 3/3 Step Cable Holder CushionAssembling the DU Lid Unit Setting the Rear CabinetDimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListPacking Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller