Matsushita CF-19FHGAX Assembly of LCD Front Case, LCD Front Assy Magnet Assy 0 0.5mm Magnet Tape

Page 40

9.2.5.Assembling the Antenna Cover, the Tablet Latch Cover and the LCD Rear Case

1.Fix the LCD Rear Case using the 10 Screws <N15> and the 2 Screws. <N16>

2.Attach the Antenna Covers and the Tablet Latch Cover to the Display Unit.

3.Tighten the 8 Screws <N7> on the back of the Display Unit.

4.Turn the Display Unit over, and tighten the 8 Screws. <N7>

Screws <N7> : DRQT26+E5FKL

Screws <N15> : DXYN2+J6FNL

Screws <N16> : DXYN3+J10FNL

■Assembly of LCD Front Case

		<N15>
		<N15>	<N16>	LCD Rear Case
	<N15>		<N16>
	<N15>		<N16>
	<N15>
	<N15>			<N15>
	Antenna Cover			<N15>
		<N7>		<N15>
				<N15>
				<N15>
	<N7>	<N7>
		<N7>
	<N7>
	<N7>			<N7>
	<N7>			<N7>
	<N7>	<N7>
		<N7>
	<N7>	<N7>	<N7>	<N7>
	<N7>
		<N7>	<N7> Antenna Cover
		<N7>	<N7> Antenna Cover
	Tablet Latch Cover

Do not use if the protrusion such as painting lump exists around D5. (Due to affect the Touch Screen operations.)

Insert it between the ribs, and attach it.

LCD Front Assy

Magnet Ass'y 0 0.5mm

Magnet Tape

0 1mm Magnet

Avoid running over	1mm (Both on the top and the side)

Tape

Avoid running over

Note for attachment

Avoid running over the display part.

Attach and apply the load 30 to 40N (3.0 to 4.0 Kgf).

Attach here Position of pasting D. 00.5mm

00.5mm

Fit to the rib 00.5mm

40 / 90

Image 40

Contents Model No. CF-19FHGAXxM How to replace the fuse For U.KLaser Safety Information Safety Precautions Precautions Battery Pack Contents Specifications Main SpecificationsWireless LAN Only for model with wireless LAN BluetoothTM Only for model with BluetoothNames and Functions of Parts SD Memory Card Indicator Blinking During access LAN PortInternal Host PCI BridgeSigmatel AC-linkDiagnosis Procedure Acng Adaptor/Battery Output voltage Power lamp Check Check Bios operationTroubleNO symptoms on some Inverter board LCD back Light lightingTable of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Touch ScreenPanel 1394Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Dimm Lid Assíy Removing the Rear CabinetRemoving the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing Pad PCB and SW PCB Removing the Display unitRemoving the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit Removing the Each Cover USBSheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB Inverter Assy LCD Side Cushion ECushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Laminate Touch Screen AssyProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Setting up the LCD Hinge Line Processing of Antenna CableCable Hold Plate Assembly of LCD HingeScrew LCD Hinge Cable Guide HInge Cable Holder S2 Fit Holders as shown in figure Until you hear the clickAssembly of LCD Front Case LCD Front Assy Magnet Assy 0 0.5mm Magnet TapeAssembly of LCD Rear Case Applicable Model Digitizer Model Marking line5mm Marking line Attach it between marking linesAssembly of Tablet Latch Cover and Antenna Cover Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Assembly of Display Unit Screw ScrewSetting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Screw HDD Connector Guide Thermal Rubber SD PCB Assy ScrewScrewDimm Holder Assy RF SW Knob Dimm HolderSetting the Audio PCB Screw Battery FPC AssySetting the Hsdpa PCB and Bluetooth PCB Line Processing of Antenna Cable of Main Unit Cable Process 1/3Step Step CableCable Process 3/3 Step Cable Holder CushionSetting the Rear Cabinet Assembling the DU Lid UnitDimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the Palm Rest Assy Putting of the KBD TapeIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Replacement Parts List Main Block UnitPacking Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller