Matsushita CF-19FHGAX Setting the left LED PCB and right LED PCB, Putting of the TP Bottom Tape

Page 46

■Assembly of the Pad PCB and SW PCB

(Note) Arrow without specified measurement: 0 to 0.5 mm

PAD PWB ASSY

PAD PWB

SW FPC

Insert

LED(R) FPC

			Insert
PAD MAIN FPC ASSY	Back side	Power SW Cable
	Back side	Power SW Cable
No direction when inserting
	Power Cable Cushion		Insert

Wrap around the Cable.

Use the fixing JIG for the pressured portion when the cables are inserted.

8 2mm

Thermistor

Insert to the connector

PAD MAIN FPC Ass'y

PAD-Main FPC

Stiffening Plate Side

Fold back
	0	1mm
0	1mm
Tape

SW PCB Ass'y

Operation Tape

Match the edge and attach it.

Avoid coming off of the LED part, or running over the LED part.

Ensure that the direction is right when attaching. The Connector bracket is on the back side.

SW PCB

Operation

Sheet

■Putting of the TP Bottom Tape

Front side

Screw

SW PCB Ass'y

Match to the upper left corner. 0 to 0.5mm

Screw

9.2.8.Setting the left LED PCB and right LED PCB

1.Connect the Cable to the Connector. (CN806)

2.Fix the left LED PCB.

3.Connect the Cable to the Connector. (CN801)

4.Fix the right LED PCB.

5.Attach the two Release Papers.

6.Attach the Palm Rest Ass'y.

Release Paper

Release Paper

left LED PCB

Connector(CN806)

right LED PCB

Connector(CN801)

46 / 90

Image 46

Contents Model No. CF-19FHGAXxM How to replace the fuse For U.KLaser Safety Information Safety Precautions Precautions Battery Pack Contents Specifications Main SpecificationsWireless LAN Only for model with wireless LAN BluetoothTM Only for model with BluetoothNames and Functions of Parts SD Memory Card Indicator Blinking During access LAN PortSigmatel InternalHost PCI Bridge AC-linkDiagnosis Procedure TroubleNO symptoms on some Acng Adaptor/Battery Output voltage Power lamp CheckCheck Bios operation Inverter board LCD back Light lightingTable of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Panel TouchScreen 1394Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Dimm Lid Assíy Removing the Rear CabinetRemoving the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing Pad PCB and SW PCB Removing the Display unitRemoving the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit Removing the Each Cover USBSheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB Cushion High Inverter AssyLCD Side Cushion E LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Protect Sheet LaminateTouch Screen Assy SpacerAssembly of Glass Applicable Model Digitizer Model Setting up the LCD Hinge Line Processing of Antenna CableCable Hold Plate Assembly of LCD HingeScrew LCD Hinge Cable Guide HInge Cable Holder S2 Fit Holders as shown in figure Until you hear the clickAssembly of LCD Front Case LCD Front Assy Magnet Assy 0 0.5mm Magnet Tape5mm Assembly of LCD Rear Case Applicable Model Digitizer ModelMarking line Marking line Attach it between marking linesAntenna Cushion L Assembly of Tablet Latch Cover and Antenna CoverAntenna Cover Screw Antenna CoverSetting the Display Unit Assembly of Display Unit Screw ScrewSetting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Dimm Holder Assy RF SW Knob Screw HDD Connector Guide Thermal Rubber SD PCB AssyScrewScrew Dimm HolderSetting the Audio PCB Screw Battery FPC AssySetting the Hsdpa PCB and Bluetooth PCB Line Processing of Antenna Cable of Main Unit Cable Process 1/3Cable Process 3/3 StepStep Cable Step Cable Holder CushionSetting the Rear Cabinet Assembling the DU Lid UnitDimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Intel Label Windows Logo Label Putting of the Palm Rest AssyPutting of the KBD Tape Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Replacement Parts List Main Block UnitPacking Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller