Matsushita CF-19FHGAX service manual Assembly of the HDD Assy

Page 65

■Assembly of the HDD ASSY

Safety Working

Heater Ass'y

Heater

0 2mm

Sub material: Pet Tape 1

(19mm width x 4 cm)

Heater Insulation Sheet

Attach on the inside of 1

Details for attachment of Heater Insulation Sheet

Two-sided Tape

Come the bottom over by 0 to 0.5 mm.

0	0.5mm	Note for the Heater top end location
			0	1mm
				Avoid any stress
		10	15mm

Insulation Parts

Insulation Parts

5 1mm

5 1mm

Heater Assy

Back

HDD

Connect the Connector

FPC(HDD)

Round to make the brown side outside and insert the notch part

Thermal Sheet

1 2mm

	Attach it on the center of the HDD.
	3mm		Revision Label Matches to	Match to the level.
			Revision Label Matches to	Match to the level.
			the center	0 to 1 mm
			2mm

HDD Case Lower

HDD Case Upper

Production

FPC Connector

Insulation Sheet

HDD Case Tab

HDD Case Lower

HDD Damper

Attach on the inner side of the HDD Case A

00.5mm

Screw

HDD Connector Guard

Screw

Attach

Remove the

Release Paper

Make the Hook inside

Hook it

65 / 90

Image 65

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessHost PCI Bridge InternalSigmatel AC-linkDiagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lightingOutline of Post Error Diagnosis by Checking Beep Signal SoundTable of errors classified by beep sounds Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394Removing the Touch Pad and Key- board Removing the Battery Pack and HDD PackPreparation Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Audio PCB Removing the Hsdpa PCB and Bluetooth PCBRemoving the DU Lid Unit HDD Removing the left LED and right Removing the Power SW PCBRemoving the I/O PCB Assy Removing the Display unit Removing Pad PCB and SW PCBRemoving Inverter PCB and LCD Unit Removing the LCD Rear CaseRemoving the LCD Hinge USB Removing the Each CoverPCB Spacer Setting up the Inverter Assy and LCD UnitSheet Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeScrew LCD Hinge Assembly of LCD HingeCable Hold Plate S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking linesAntenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Putting of the TP Bottom Tape Setting the left LED PCB and right LED PCBAssembly of the Pad PCB and SW PCB Assembly of the Power SW PCB Setting the Power SW PCBAssembly of the left LED PCB and right LED PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm HolderScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable StepCable Process 3/3 Step Cable Holder CushionAssembling the DU Lid Unit Setting the Rear CabinetBottom Rubber Tape Bottom Case Assy Setting the Dimm Lid AssyDimm Thermal Sheet Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListMechanical Parts AccessoriesPacking Material DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller