Matsushita CF-19FHGAX service manual DFHG429YA IO DC Tube

Page 79

K141	DFHG429YA	IO DC TUBE		1
K142	DFHR3G38ZA	DIMM CUSHION		3
K144	DFHP7270ZA	ADHESIVE TAPE	NRP	4
K157	DFMX1339ZA	BAT INSULATION SHEET	NRP	1
K158	DFHR3J82ZA	LCD CABLE PROTECTER		1
K159	DFHR6352ZA	CABLE GUIDE HINGE		1
K160	DFHR3F89ZA	MCH SHEET	NRP	1
K161	DFHR3H64ZA	COIN BAT SHEET	NRP	1
K162	DFHR6353ZA	LAN CONN HOLDER		1
K163	DFMC0901ZA	GASKET-65TSV13-1(T9)-1.9		1
K164	DFMY0472ZA	THERMAL RUBBER CPU		1
K165	DFMY0475ZA	ICH RUBBER		2
K166	DFHR3650ZA	WATERPROOF SHEET	NRP	1
K167	DFHR3H95ZA	LCD TS PWB SHEET	NRP	1
K1051	DFMY3264YA	DIMM THERMAL SHEET	NRP	1
K1603	DFHR6339ZA-0	DUMMY EXPRESS CARD		1
K1604	DFHR6340ZA-0	DUMMY PC CARD		1
K1610	DFHR3J11ZA	PCMCIA DUMMY CARD CUSHION		1
N1	DFHE5025XA	SCREW		33
N2	DFHE5058ZB	SCREW		4
N3	DFHE5108ZA	SCREW		4
N4	DRHM0112ZA	SCREW		2
N5	DRHM0115ZA	SCREW		2
N6	DRHM5025YA	SCREW		18
N7	DRQT26+E5FKL	SCREW		18
N8	DRSB2+10FKL	SCREW		2
N9	DRSB2+5FKL	SCREW		27
N10	DRHM0061ZA	SCREW		13
N11	DRYN3+J6FKL	SCREW		2
N14	DRQT3+E4FKL	SCREW		2
N15	DXYN2+J6FNL	SCREW		10
N16	DXYN3+J10FNL	SCREW		2
N17	DXYN3+J8FNL	SCREW		2
N18	DXYN4+J8FNL	SCREW		4
N19	XSB2+3FNL	SCREW		17

79 / 90

Image 79

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessAC-link InternalHost PCI Bridge SigmatelDiagnosis Procedure Inverter board LCD back Light lighting Acng Adaptor/Battery Output voltage Power lamp CheckCheck Bios operation TroubleNO symptoms on someTable of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS 1394 TouchScreen PanelPreparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCBRemoving the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit USB Removing the Each CoverSheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB LCD Side Cushion E TS PWB LCD Side Cushion Voltage Label Inverter AssyLCD Side Cushion E Cushion HighAssembly of Inverter PCB Application Model Digitizer Model Spacer LaminateTouch Screen Assy Protect SheetAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeCable Hold Plate Assembly of LCD HingeScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Attach it between marking lines Assembly of LCD Rear Case Applicable Model Digitizer ModelMarking line 5mmScrew Antenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cover Antenna Cushion LSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Dimm Holder Screw HDD Connector Guide Thermal Rubber SD PCB AssyScrewScrew Dimm Holder Assy RF SW KnobScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable Holder Cushion StepStep Cable Cable Process 3/3Assembling the DU Lid Unit Setting the Rear CabinetDimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Energy Star Label Putting of the Palm Rest AssyPutting of the KBD Tape Intel Label Windows Logo LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListPacking Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller