Matsushita CF-19FHGAX service manual Cable Guide HInge Cable Holder

Page 39

■Line Processing of Antenna Cable and LCD Cable Safety Working

CAUTION	S1:Insulation S2:Pinching Cables S3:Sharp Edge
CAUTION	S4:Part No. Check S5:Others
Step1	Step2
	Cable Holder

Install the Holder and Cable guide on the Hinge as shown in figure.

Cable Guide HInge

Cable Holder

Insert the cables into the Cable Holder as shown in figure. <CAUTION>:Position of the Antenna Cables

Right side of LCD Cable:White/Gray Left side of LCD Cable:Blue/Black/Brown

Keep margin in cable length

It prevents to break of the cable

Step3

Red marking is on the holder

Black marking is on the holder

S2 Fit Holders as shown in figure

(Until you hear the click)

Watch out is the cable comes off from the holder

for cable is not scissored between the holder and hinge.

Step4

S5

LCD cable proccess space

ANT cable proccess space

Wrap (one round) only the Antenna Cables around

the axis of the Hinge as shown in figure.

Note: Handle LCD cable as show in figure. LCD cable must not intersect with Antenna Cables.

CAUTION:Check the position of the Cables

Step5

Next, wrap (one round) the LCD Cable around the axis of the Hinge as shown in figure.

Step6

OK

It prevents to break of the cable

S5

NG

The antenna cables must not intersect with the LCD cable.

39 / 90

Image 39

Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessAC-link InternalHost PCI Bridge SigmatelDiagnosis Procedure Inverter board LCD back Light lighting Acng Adaptor/Battery Output voltage Power lamp CheckCheck Bios operation TroubleNO symptoms on someError Diagnosis by Checking Beep Signal Sound Table of errors classified by beep soundsOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS 1394 TouchScreen PanelRemoving the Battery Pack and HDD Pack PreparationRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Hsdpa PCB and Bluetooth PCB Removing the DU Lid UnitRemoving the Audio PCB HDD Removing the Power SW PCB Removing the I/O PCB AssyRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCBRemoving the LCD Rear Case Removing the LCD HingeRemoving Inverter PCB and LCD Unit USB Removing the Each CoverSetting up the Inverter Assy and LCD Unit SheetPCB Spacer Assembly of Inverter PCB LCD Side Cushion E TS PWB LCD Side Cushion Voltage Label Inverter AssyLCD Side Cushion E Cushion HighAssembly of Inverter PCB Application Model Digitizer Model Spacer LaminateTouch Screen Assy Protect Sheet Assembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeAssembly of LCD Hinge Cable Hold PlateScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Attach it between marking lines Assembly of LCD Rear Case Applicable Model Digitizer ModelMarking line 5mmScrew Antenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cover Antenna Cushion LSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Setting the left LED PCB and right LED PCB Assembly of the Pad PCB and SW PCBPutting of the TP Bottom Tape Setting the Power SW PCB Assembly of the left LED PCB and right LED PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Dimm Holder Screw HDD Connector Guide Thermal Rubber SD PCB AssyScrewScrew Dimm Holder Assy RF SW KnobScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable Holder Cushion StepStep Cable Cable Process 3/3Assembling the DU Lid Unit Setting the Rear CabinetSetting the Dimm Lid Assy Dimm Thermal SheetBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Energy Star Label Putting of the Palm Rest AssyPutting of the KBD Tape Intel Label Windows Logo LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListAccessories Packing MaterialMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller