Matsushita CF-19FHGAX service manual Preparation, Removing the Battery Pack and HDD Pack

Page 23

9 Disassembly/Reassembly

Note:

Power off the computer. Do not shut down to the Suspend or hibernation mode.

Do not add peripherals while the computer is in the Suspend or hibernation mode; abnormal operation may result.

9.1.Disassembly Instructions

9.1.1.Preparation

Before disassembling, be sure to make the following prepara- tions.

ï Shut down Windows and turn off the power.

ï Disconnect the AC adaptor.

ï Remove the optional DIMM memory card and PCMCIA card

if they are connected.

HDD Case B

Hooks

HDD FPC

HDD

Hooks

ï Remove other devices if they are connected.

Attention:

ïPlease execute writing BIOS ID when you exchange the Main Board.

ïParts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.

9.1.2.Removing the Battery Pack and HDD Pack

Heater

<N13>

<N13>

HDD Case A

1

2

 

5.

Remove the two Screws <N13>.

 

6.

Remove the HDD Case A and the HDD Case B.

3

7.

Remove the HDD

Screws <N13> : DXQT2+D4FNL

9.1.3. Removing the Touch Pad and Key- board

KBD Plate

 

<N9>

 

 

<N9>

KBD Plate

 

 

Palm Rest Ass'y

 

<N9>

 

<N9>

 

 

HDD Pack

Battery Pack

1. Open the Battery Cover. 2. Remove the Battery Pack.

3. Open the HDD Cover.

4. Remove the HDD Pack.

1. Remove the Palm Rest Ass'y.

Note:

The Palm Rest Ass'y is firmly fixed with two-sided tape.

Carefully remove the Palm Top Cover Sheet not to damage it.

2. Remove the 4 Screws <N9>.

3. Remove the KBD Plate.

23 / 90

Image 23
Contents Model No. CF-19FHGAXxM For U.K How to replace the fuseLaser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications SpecificationsBluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LANNames and Functions of Parts LAN Port SD Memory Card Indicator Blinking During accessAC-link InternalHost PCI Bridge SigmatelDiagnosis Procedure Inverter board LCD back Light lighting Acng Adaptor/Battery Output voltage Power lamp CheckCheck Bios operation TroubleNO symptoms on someOutline of Post Error Diagnosis by Checking Beep Signal SoundTable of errors classified by beep sounds Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS 1394 TouchScreen PanelRemoving the Touch Pad and Key- board Removing the Battery Pack and HDD PackPreparation Removing the Rear Cabinet Removing the Dimm Lid AssíyRemoving the Audio PCB Removing the Hsdpa PCB and Bluetooth PCBRemoving the DU Lid Unit HDD Removing the left LED and right Removing the Power SW PCBRemoving the I/O PCB Assy Removing the Display unit Removing Pad PCB and SW PCBRemoving Inverter PCB and LCD Unit Removing the LCD Rear CaseRemoving the LCD Hinge USB Removing the Each CoverPCB Spacer Setting up the Inverter Assy and LCD UnitSheet Assembly of Inverter PCB LCD Side Cushion E TS PWB LCD Side Cushion Voltage Label Inverter AssyLCD Side Cushion E Cushion HighAssembly of Inverter PCB Application Model Digitizer Model Spacer LaminateTouch Screen Assy Protect SheetAssembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD HingeScrew LCD Hinge Assembly of LCD HingeCable Hold Plate S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable HolderLCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front CaseMarking line Attach it between marking lines Assembly of LCD Rear Case Applicable Model Digitizer ModelMarking line 5mmScrew Antenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cover Antenna Cushion LSetting the Display Unit Screw Screw Assembly of Display UnitSetting the Pad PCB and SW PCB Putting of the TP Bottom Tape Setting the left LED PCB and right LED PCBAssembly of the Pad PCB and SW PCB Assembly of the Power SW PCB Setting the Power SW PCBAssembly of the left LED PCB and right LED PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Dimm Holder Screw HDD Connector Guide Thermal Rubber SD PCB AssyScrewScrew Dimm Holder Assy RF SW KnobScrew Battery FPC Assy Setting the Audio PCBSetting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main UnitStep Cable Holder Cushion StepStep Cable Cable Process 3/3Assembling the DU Lid Unit Setting the Rear CabinetBottom Rubber Tape Bottom Case Assy Setting the Dimm Lid AssyDimm Thermal Sheet Setting the Touch Pad and Keyboard Putting of the Sheet Energy Star Label Putting of the Palm Rest AssyPutting of the KBD Tape Intel Label Windows Logo LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts ListMechanical Parts AccessoriesPacking Material DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller