Matsushita CF-19FHGAX service manual Safety Precautions

Page 4

SAFETY PRECAUTIONS

1.Before servicing, unplug the power cord to prevent an electric shock.

2.When replacing parts, use only manufacture's recommended components for safety.

3.Check the condition of the power cord. Replace if wear or damage is evident.

4.After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1.Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

3.Do not use the telephone to report a gas leak in the vicinity of the leak. vicinity of the leak.

4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

SAVE THESE INSTRUCTIONS

LITHIUM BATTERY

This computer contains a lithium battery to enable the date, time, and other data to be stored. The battery should only be exchanged by authorized service personel.

Warning! A risk of explosion from incorrect installation or misapplication may possibly occur.

LITHIUM BATTERY

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the equipment manufacturer. Dispose of used batteries according to the manufacturer's instructions.

LITHIUMBATTERIES

Vorsicht!

Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben order einen vom Hersteller empfohlenen ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

PILE AU LITHIUM

ATTENTION: IL Y A DANGER D'EXPLOSION S' IL Y A REMPLACEMENT INCORRECT DE LA PILE. REMPLACER UNIQUEMENT AVEC UNE PILE DU MÈME TYPE OU D'UN TYPE RECOMMANDÉ PAR LE CONSTRUCTEUR. METTRE AU RÉBUT LES PILES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT.

4 / 90

Image 4
Contents Model No. CF-19FHGAXxM How to replace the fuse For U.KLaser Safety Information Safety Precautions Precautions Battery Pack Contents Specifications Main SpecificationsWireless LAN Only for model with wireless LAN BluetoothTM Only for model with BluetoothNames and Functions of Parts SD Memory Card Indicator Blinking During access LAN PortInternal Host PCI BridgeSigmatel AC-linkDiagnosis Procedure Acng Adaptor/Battery Output voltage Power lamp Check Check Bios operationTroubleNO symptoms on some Inverter board LCD back Light lightingTable of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Touch ScreenPanel 1394Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Dimm Lid Assíy Removing the Rear CabinetRemoving the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing Pad PCB and SW PCB Removing the Display unitRemoving the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit Removing the Each Cover USBSheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB Inverter Assy LCD Side Cushion ECushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Laminate Touch Screen AssyProtect Sheet SpacerAssembly of Glass Applicable Model Digitizer Model Setting up the LCD Hinge Line Processing of Antenna CableCable Hold Plate Assembly of LCD HingeScrew LCD Hinge Cable Guide HInge Cable Holder S2 Fit Holders as shown in figure Until you hear the clickAssembly of LCD Front Case LCD Front Assy Magnet Assy 0 0.5mm Magnet TapeAssembly of LCD Rear Case Applicable Model Digitizer Model Marking line5mm Marking line Attach it between marking linesAssembly of Tablet Latch Cover and Antenna Cover Antenna CoverAntenna Cushion L Screw Antenna CoverSetting the Display Unit Assembly of Display Unit Screw ScrewSetting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Screw HDD Connector Guide Thermal Rubber SD PCB Assy ScrewScrewDimm Holder Assy RF SW Knob Dimm HolderSetting the Audio PCB Screw Battery FPC AssySetting the Hsdpa PCB and Bluetooth PCB Line Processing of Antenna Cable of Main Unit Cable Process 1/3Step Step CableCable Process 3/3 Step Cable Holder CushionSetting the Rear Cabinet Assembling the DU Lid UnitDimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the Palm Rest Assy Putting of the KBD TapeIntel Label Windows Logo Label Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Replacement Parts List Main Block UnitPacking Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller