Matsushita CF-19FHGAX service manual Assembly of LCD Hinge, Cable Hold Plate, Screw LCD Hinge

Page 38

■Assembly of LCD Hinge

Initial Condition of LCD Hinge

Cable Hold Plate

S3

Ensure the"C" side comes to thelowerright corner when viewing from above.

Cable Hold Plate

Using the fixing jig when fixing the Hinge

Fix

Fix

Tighten

Rotation Direction

Screw

LCD Hinge

Safety Working

		S2
	Avoid catching the Cable.		If you arrange the Cable in the area,
			you do not need to use the fixing jig.
Screw
	Avoid catching the Cable (when repairing or when not using the jig).

Temporarily fix the both sides ("A") of the Hinge using the Screw, and fix the Cable Hold Plate. After fixing the Cable Hold Plate, remove the screws from the both sides ("A").

CAUTION	S1:Insulation S2:Pinching Cables S3:Sharp Edge
CAUTION	S4:Part No. Check S5:Others

38 / 90

Image 38

Contents Model No. CF-19FHGAXxM How to replace the fuse For U.KLaser Safety Information Safety Precautions Precautions Battery Pack Contents Specifications Main SpecificationsWireless LAN Only for model with wireless LAN BluetoothTM Only for model with BluetoothNames and Functions of Parts SD Memory Card Indicator Blinking During access LAN PortSigmatel InternalHost PCI Bridge AC-linkDiagnosis Procedure TroubleNO symptoms on some Acng Adaptor/Battery Output voltage Power lamp CheckCheck Bios operation Inverter board LCD back Light lightingOutline of Post Error Diagnosis by Checking Beep Signal SoundTable of errors classified by beep sounds Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Panel TouchScreen 1394Removing the Touch Pad and Key- board Removing the Battery Pack and HDD PackPreparation Removing the Dimm Lid Assíy Removing the Rear CabinetRemoving the Audio PCB Removing the Hsdpa PCB and Bluetooth PCBRemoving the DU Lid Unit HDD Removing the left LED and right Removing the Power SW PCBRemoving the I/O PCB Assy Removing Pad PCB and SW PCB Removing the Display unitRemoving Inverter PCB and LCD Unit Removing the LCD Rear CaseRemoving the LCD Hinge Removing the Each Cover USBPCB Spacer Setting up the Inverter Assy and LCD UnitSheet Assembly of Inverter PCB Cushion High Inverter AssyLCD Side Cushion E LCD Side Cushion E TS PWB LCD Side Cushion Voltage LabelAssembly of Inverter PCB Application Model Digitizer Model Protect Sheet LaminateTouch Screen Assy SpacerAssembly of Glass Applicable Model Digitizer Model Setting up the LCD Hinge Line Processing of Antenna CableScrew LCD Hinge Assembly of LCD HingeCable Hold Plate Cable Guide HInge Cable Holder S2 Fit Holders as shown in figure Until you hear the clickAssembly of LCD Front Case LCD Front Assy Magnet Assy 0 0.5mm Magnet Tape5mm Assembly of LCD Rear Case Applicable Model Digitizer ModelMarking line Marking line Attach it between marking linesAntenna Cushion L Assembly of Tablet Latch Cover and Antenna CoverAntenna Cover Screw Antenna CoverSetting the Display Unit Assembly of Display Unit Screw ScrewSetting the Pad PCB and SW PCB Putting of the TP Bottom Tape Setting the left LED PCB and right LED PCBAssembly of the Pad PCB and SW PCB Assembly of the Power SW PCB Setting the Power SW PCBAssembly of the left LED PCB and right LED PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit Dimm Holder Assy RF SW Knob Screw HDD Connector Guide Thermal Rubber SD PCB AssyScrewScrew Dimm HolderSetting the Audio PCB Screw Battery FPC AssySetting the Hsdpa PCB and Bluetooth PCB Line Processing of Antenna Cable of Main Unit Cable Process 1/3Cable Process 3/3 StepStep Cable Step Cable Holder CushionSetting the Rear Cabinet Assembling the DU Lid UnitBottom Rubber Tape Bottom Case Assy Setting the Dimm Lid AssyDimm Thermal Sheet Setting the Touch Pad and Keyboard Putting of the Sheet Intel Label Windows Logo Label Putting of the Palm Rest AssyPutting of the KBD Tape Energy Star LabelSetting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Replacement Parts List Main Block UnitMechanical Parts AccessoriesPacking Material DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller