Ositech comm Trumpcard Data/Fax Modem manual Ending Your Connection

Page 27

 

 

Basic Modem Operation

Short

Long

Description

 

Form

Form

 

 

62

CONNECT 24000

connection at 24000 bps

*

63

CONNECT 26400

connection at 26400 bps

*

64

CONNECT 28800

connection at 28800 bps

*

66COMPRESSION CLASS 5 MNP data compression

67COMPRESSION V.42BIS V.42bis data compression

69

COMPRESSION NONE

no compression

76

PROTOCOL NONE

connection with Modem that does

 

 

not support MNP or V.42

77

PROTOCOL: LAP-M

connection with Modem that

 

 

supports V.42

80

PROTOCOL: ALT

connection with Modem that

 

 

supports MNP

81

PROTOCOL: ALT - CELLULAR

 

 

connection with Modem that

 

 

supports MNP-10

*Only applicable to Trumpcard 28800 version

Ending Your Connection

To end your connection, log off the remote system (if applicable), enter the escape sequence (+++), and issue the ATH command.

You may want to wait 30 seconds or so after your last transmission before disconnecting to ensure any data in the Modem buffer has cleared.

Setting Up for a Non-Error Correcting Connection

The Trumpcard Modem supports the V.42 and MNP error correction protocol as its default mode. When you initiate a connection from your Trumpcard Modem to a remote Modem not supporting error correction, the remote system may respond with garbled characters or even lock up.

If the remote Modem does not support error correction, the Trumpcard continues the connection without error correction or data compression. However, as mentioned, the remote system may have already locked up. In these cases, you must break the connection, turn off error correction on the Trumpcard, and place your call again.

To turn off error correction for the Trumpcard, use the AT&Q6 command. If you wish to make this (non-error correcting) the default setting, follow the AT&Q6 command with the AT&W command.

User’s Guide and Reference

4 - 7

Image 27
Contents User’s Guide and Reference Trumpcard Data/Fax ModemHow To Contact Us CopyrightFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode FeaturesCellular Mode Facsimile ModeUnique Features Industry Standards 22bis32bis 27ter 42bisMNP 2, 3, MNPPreparing for Installation Hardware InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You BeginOperating the Trumpcard Using AT CommandsTone or Pulse Dialling Making an Outgoing CallRe-Dialling the Last Number Storing a NumberConnection Messages Carrier Connect 1200TX/75RXFAX DataEnding Your Connection Setting Up for a Non-Error Correcting ConnectionReceiving an Incoming Call Setting up for a Cellular ConnectionModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command SummaryModem Command Reference Modem Command Descriptions Re-executeAnswer ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0ATDS=2 Fn Select Line Modulation 14400 only En Command EchoSub-parameter Definitions +Ms Select Line Modulation 28800 onlyATH1 Hn Switch-Hook ControlVFC ATH0Identification OlumeMn Speaker Control On Return To The On-Line State Nn Automode DetectionATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S RegistersSet Tone Dial as Default Vn Result Code FormWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Zn Reset Yn Control Long Space DisconnectCn DCD Option Restore Factory Configuration Dn DTR OptionNone Gn Set Guard Tone Jn T elephone Jack SelectionKn DTE/Modem Flow Control Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication ModeSn DSR Option Rn RTS/CTS OptionTn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7Wn Store User Profile Yn Designate Default User Profile\Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow ControlAT\K1 AT\K3AT\K5 Cn Compression Control \Nn Operation Mode ControlEn Enable/Disable Line Quality Monitor Report Received Signal LevelReport Line Signal Quality Kn MNP Extended Services Mn T ransmit Level Adjustment for Cellular ConnectionHn Link Negotiation Speed En Compromise Equalizer @Mn Initial Cellular Power LevelInit string = Null Init string Event Based CommandDefault Register Settings Modem S RegistersModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After DialS12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one DurationS30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTRS32 XON Character S33 Xoff CharacterS36 Lapm Failure Control S37 Desired Telco Line Speed Range DefaultS46 Protocol Selection S38 Delay Before Forced DisconnectS86 Connection Failure Cause Code S48 V .42 Negotiation ActionS95 Extended Result Codes Facsimile Commands Class 1 CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Testing Modem Memory Product InformationROM Checksum Test