Ositech comm Trumpcard Data/Fax Modem manual Init string Event Based Command, Init string = Null

Page 65

Modem Command Reference

.

AT@M30-30dBm

AT@M31-31dBm

[n init string] — Event Based Command

Parameters	n = 0 or 1
	init string = any valid AT command(s) except
	Z (reset)
Defaults	n = 0
	init string = NULL

The event based command is unique in that it allows single or multiple AT commands to be associated with an event identified by an event identifier “n”. Currently only two events are identified; event 0 indicates that the modem is currently operating using a land line based communication line; event 1 indicates that the modem is currently operating using a cellular based communications line. These events can change dynamically, and thus whenever a change is detected the modem will execute the AT commands associated with the event automatically.

Multiple event based commands can be on the same command line or can be entered on separate command lines. The AT command(s) associated with an event are stored in volatile memory, powering off the modem or executing the ATZ command will clear the command(s). A NULL init string will also serve as a way of clearing command(s) associated with an event.

All commands between the [n and then next], or [n, or the end of the command line will be associated with the event n. All commands will be verified and commands that require interaction or return information should not be used since these will be executed based on changing events.

Examples

AT[0&F&C1&D2&S1W1S95=18]

The above command stores the &F&C1&D2&S1W1S95=18 commands for event 0 (land based connection) and will be automatically executed when a change of event from cellular back to land based is detected.

AT&F&C1&D2&S1[0S95=18][1S95=44)M1*H2:E0]

User’s Guide and Reference

4 - 33

Image 65

Contents User’s Guide and Reference Trumpcard Data/Fax ModemFTP How To Contact UsCopyright Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode FeaturesCellular Mode Facsimile ModeUnique Features 32bis Industry Standards22bis MNP 2, 3, 42bisMNP 27terPreparing for Installation Hardware InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You BeginOperating the Trumpcard Using AT CommandsTone or Pulse Dialling Making an Outgoing CallConnection Messages Re-Dialling the Last NumberStoring a Number FAX Connect 1200TX/75RXData CarrierEnding Your Connection Setting Up for a Non-Error Correcting ConnectionReceiving an Incoming Call Setting up for a Cellular ConnectionModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command SummaryModem Command Reference Answer Modem Command DescriptionsRe-execute Dn Dial Bn Set ITU-T or Bell ModeATB0 ATB1ATDS=2 Fn Select Line Modulation 14400 only En Command EchoSub-parameter Definitions +Ms Select Line Modulation 28800 onlyVFC Hn Switch-Hook ControlATH0 ATH1Mn Speaker Control IdentificationOlume On Return To The On-Line State Nn Automode DetectionQn Result Code Display Set Pulse Dial as DefaultSn Read/Write S Registers ATQ0Wn Connect Message Control Set Tone Dial as DefaultVn Result Code Form Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Cn DCD Option Zn ResetYn Control Long Space Disconnect None Restore Factory ConfigurationDn DTR Option Kn DTE/Modem Flow Control Gn Set Guard ToneJn T elephone Jack Selection Pn Dial Pulse Ratio disabled for the U.S Mn Communication ModeQn Communication Mode Ln Line TypeSn DSR Option Rn RTS/CTS OptionTn T est and Diagnostic AT&T6 View Configuration and User ProfilesAT&T7 AT&T8Wn Store User Profile Yn Designate Default User Profile\Bn T ransmit Break Zn=x Store Phone Number\Gn Modem-to-Modem Flow Control \Kn Break ControlAT\K5 AT\K1AT\K3 Cn Compression Control \Nn Operation Mode ControlReport Line Signal Quality En Enable/Disable Line Quality MonitorReport Received Signal Level Hn Link Negotiation Speed Kn MNP Extended ServicesMn T ransmit Level Adjustment for Cellular Connection En Compromise Equalizer @Mn Initial Cellular Power LevelInit string = Null Init string Event Based CommandModem Register Summary Default Register SettingsModem S Registers Modem Command Reference S95 Extended Result Codes Register Descriptions S6 Wait S5 Backspace CharacterS7 Wait For Carrier After Dial S8 PauseS9 Carrier Detect Response Time S10 Lost Carrier To Hang Up DelayS11 Dtmf T one Duration S12 Escape Code Guard TimeS24 Sleep Inactivity Timer S18 Test TimerS25 Delay to DTR S30 Inactivity TimerS36 Lapm Failure Control S32 XON CharacterS33 Xoff Character S37 Desired Telco Line Speed Range DefaultS46 Protocol Selection S38 Delay Before Forced DisconnectS86 Connection Failure Cause Code S48 V .42 Negotiation ActionS95 Extended Result Codes Class 2 Commands Facsimile CommandsClass 1 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback ROM Checksum Test Testing Modem MemoryProduct Information