Ositech comm Trumpcard Data/Fax Modem manual ATDS=2

Page 40

Section Four

@Causes the modem to listen for 5 seconds of silence. If a 5 second silence has not been detected within the period specified in S7 (default = 30 seconds), the modem disconnects and returns the NO ANSWER result code. If it detects a busy signal, it returns a BUSY result code. If the 5 seconds of silence is detected, then the modem continues dialling the dial string.

WWait For Dial Tone Before Dialling. Causes the modem to wait for a dial tone up to the period of time specified in register S7 (default = 30 seconds) before dialling the numbers that follow. If the modem detects a dial tone before the given time delay, it continues to dial. Otherwise, it goes on-hook.

,Pause During Dial. Inserted between digits in a dial string. Causes the modem to pause for the value given by register S8 (default = 2 seconds), before dialling the next digit. This delay can be used in place of the "Wait For Dial Tone Before Dialling", but is not as sophisticated.

;Return To Command Mode After Dialling. Added to the end of a dial string. Causes the modem to remain in the command mode after it dials the digits proceeding the command. This allows the user to issue additional dial commands or dial strings without overflowing the command buffer. The modem looks for the carrier after the final dial command is issued. The Command ATHn aborts this command.

^Turn On Calling Tone. Turns on the periodic 1300 Hz calling tone if originating the call. Calling tone is enabled only on a call-by-call basis.

S=n Dial Stored Number. Follows the dial command string. Causes the modem to dial a telephone number previously stored in directory location n using &Zn command.

If ATD is entered without parameters, the modem goes off-hook and waits for a carrier; if the handshake is not completed within the specified time by register S7 (default = 30 seconds), the modem goes on-hook.

The Dial command will be aborted in progress upon receipt of any character before completion of the handshake.

Examples

ATDT1-800-555-1212 Dial long distance number

ATDT9,555-4444

Inserted pause

ATDS=2

Dial stored number

4 - 8

Trumpcard 14400/28800 Modem

Image 40
Contents Trumpcard Data/Fax Modem User’s Guide and ReferenceCopyright How To Contact UsFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Features Data ModeFacsimile Mode Cellular ModeUnique Features 22bis Industry Standards32bis 42bis MNP 2, 3,MNP 27terHardware Installation Preparing for InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Before You Begin Enabling The TrumpcardUsing AT Commands Operating the TrumpcardMaking an Outgoing Call Tone or Pulse DiallingStoring a Number Re-Dialling the Last NumberConnection Messages Connect 1200TX/75RX FAXData CarrierSetting Up for a Non-Error Correcting Connection Ending Your ConnectionSetting up for a Cellular Connection Receiving an Incoming CallModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference Modem Command Summary +MSModem Command Reference Re-execute Modem Command DescriptionsAnswer Bn Set ITU-T or Bell Mode Dn DialATB0 ATB1ATDS=2 En Command Echo Fn Select Line Modulation 14400 only+Ms Select Line Modulation 28800 only Sub-parameter DefinitionsHn Switch-Hook Control VFCATH0 ATH1Olume IdentificationMn Speaker Control Nn Automode Detection On Return To The On-Line StateSet Pulse Dial as Default Qn Result Code DisplaySn Read/Write S Registers ATQ0Vn Result Code Form Set Tone Dial as DefaultWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Yn Control Long Space Disconnect Zn ResetCn DCD Option Dn DTR Option Restore Factory ConfigurationNone Jn T elephone Jack Selection Gn Set Guard ToneKn DTE/Modem Flow Control Mn Communication Mode Pn Dial Pulse Ratio disabled for the U.SQn Communication Mode Ln Line TypeRn RTS/CTS Option Sn DSR OptionTn T est and Diagnostic View Configuration and User Profiles AT&T6AT&T7 AT&T8Yn Designate Default User Profile Wn Store User ProfileZn=x Store Phone Number \Bn T ransmit Break\Gn Modem-to-Modem Flow Control \Kn Break ControlAT\K3 AT\K1AT\K5 \Nn Operation Mode Control Cn Compression ControlReport Received Signal Level En Enable/Disable Line Quality MonitorReport Line Signal Quality Mn T ransmit Level Adjustment for Cellular Connection Kn MNP Extended ServicesHn Link Negotiation Speed @Mn Initial Cellular Power Level En Compromise EqualizerInit string Event Based Command Init string = NullModem S Registers Default Register SettingsModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S5 Backspace Character S6 WaitS7 Wait For Carrier After Dial S8 PauseS10 Lost Carrier To Hang Up Delay S9 Carrier Detect Response TimeS11 Dtmf T one Duration S12 Escape Code Guard TimeS18 Test Timer S24 Sleep Inactivity TimerS25 Delay to DTR S30 Inactivity TimerS33 Xoff Character S32 XON CharacterS36 Lapm Failure Control Range Default S37 Desired Telco Line SpeedS38 Delay Before Forced Disconnect S46 Protocol SelectionS48 V .42 Negotiation Action S86 Connection Failure Cause CodeS95 Extended Result Codes Class 1 Commands Facsimile CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Product Information Testing Modem MemoryROM Checksum Test