Ositech comm Trumpcard Data/Fax Modem manual Hn Switch-Hook Control, Vfc, ATH0, ATH1

Page 43

		Modem Command Reference
9	V.32	9600 or 4800
10	V.32bis	14400, 12000, 9600, 7200, or 4800

11V.34 28800, 26400, 24000, 21600, 19200, 16800, 14400, 12000, 9600, 7200, 4800, or 2400

64	Bell	103	300
69	Bell	212	1200
74	VFC		28800, 26400, 24000, 21600, 16800, or 14400

2.<automode> is an optional numeric value which enables or disables automatic modulation negotiation using V.8 or V.32bis annex a. The options are:

<automode>	Option Selected	Notes
0	Automode disabled
1	Automode enabled using V.8 or V32bis annex A Default

3.<min_rate> is an optional number which specifies the lowest rate at which the modem may establish a connection. The value is decimal coded, in units of bps, e.g., 2400 specifies the lowest rate to be 2400 bps. the default is 300 for 300 bps

4.<max_rate> is an optional number which specifies the highest rate at which the modem may establish a connection the value is decimal coded, in units of bps, eg., 14400 specifies the highest rate to be 14400 bps. the default is 28800 for 28800 bps

Hn — Switch-Hook Control

Parameters

0 or 1

Default0

If the user enters the command mode from the data mode issuing the escape sequence(+++), or as a result of an ON-to-OFF transition of DTR with the &D1 option in effect, the user may cause the modem to go on- hook (disconnect) by issuing the H0 command.

Examples

ATH0	Causes the modem to go on-hook (hang-up)
ATH1	If the modem is on-hook, modem goes off hook,
	returns an OK response, and awaits further
	commands

User’s Guide and Reference

4 - 11

Image 43

Contents User’s Guide and Reference Trumpcard Data/Fax ModemCopyright How To Contact UsFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode FeaturesCellular Mode Facsimile ModeUnique Features 22bis Industry Standards32bis 27ter 42bisMNP 2, 3, MNPPreparing for Installation Hardware InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You BeginOperating the Trumpcard Using AT CommandsTone or Pulse Dialling Making an Outgoing CallStoring a Number Re-Dialling the Last NumberConnection Messages Carrier Connect 1200TX/75RXFAX DataEnding Your Connection Setting Up for a Non-Error Correcting ConnectionReceiving an Incoming Call Setting up for a Cellular ConnectionModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command SummaryModem Command Reference Re-execute Modem Command DescriptionsAnswer ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0ATDS=2 Fn Select Line Modulation 14400 only En Command EchoSub-parameter Definitions +Ms Select Line Modulation 28800 onlyATH1 Hn Switch-Hook ControlVFC ATH0Olume IdentificationMn Speaker Control On Return To The On-Line State Nn Automode DetectionATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S RegistersVn Result Code Form Set Tone Dial as DefaultWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Yn Control Long Space Disconnect Zn ResetCn DCD Option Dn DTR Option Restore Factory ConfigurationNone Jn T elephone Jack Selection Gn Set Guard ToneKn DTE/Modem Flow Control Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication ModeSn DSR Option Rn RTS/CTS OptionTn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7Wn Store User Profile Yn Designate Default User Profile\Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow ControlAT\K3 AT\K1AT\K5 Cn Compression Control \Nn Operation Mode ControlReport Received Signal Level En Enable/Disable Line Quality MonitorReport Line Signal Quality Mn T ransmit Level Adjustment for Cellular Connection Kn MNP Extended ServicesHn Link Negotiation Speed En Compromise Equalizer @Mn Initial Cellular Power LevelInit string = Null Init string Event Based CommandModem S Registers Default Register SettingsModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After DialS12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one DurationS30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTRS33 Xoff Character S32 XON CharacterS36 Lapm Failure Control S37 Desired Telco Line Speed Range DefaultS46 Protocol Selection S38 Delay Before Forced DisconnectS86 Connection Failure Cause Code S48 V .42 Negotiation ActionS95 Extended Result Codes Class 1 Commands Facsimile CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Product Information Testing Modem MemoryROM Checksum Test