Ositech comm Trumpcard Data/Fax Modem manual S5 Backspace Character, S6 Wait, S8 Pause

Page 70

Section Four

S5 — Backspace Character

Range

0-32, ASCII decimal

Default

8 (Backspace)

Sets the character recognized as a backspace. Pertains to asynchronous operation only. The modem will not recognize the Backspace character if it is set to a value that is greater than 32 ASCII. This character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local communications software the Backspace character, an ASCII space character, and a second Backspace character; this means a total of three characters are transmitted each time the modem processes the Backspace character.

S6 — Wait

Time for Blind Dialling

Range

2-255 seconds

Default

2

Sets the length of time to pause after the modem goes off-hook and before the modem dials the first digit of the telephone number. The modem always pauses a minimum of 2 seconds even if the S6 register is set to a value less than 2 seconds. The "Wait for Dial Tone" call progress feature (W in the dial string) will override the value in register S6. If option X2 or X4 is in effect, this register is ignored.

S7 — Wait For Carrier After Dial

Range

1-255 seconds

Default50

Defines two delay times:

1.During call establishment, this register establishes the time that the local modem waits for carrier from the remote modem before hanging up.

2.Sets the length of time that the modem waits when the "Wait For Dial Tone" call progress feature (W in the dial string) is in effect.

S8 — Pause

Time For Dial Delay

Range

0-255 seconds

4 - 38

Trumpcard 14400/28800 Modem

Image 70
Contents Trumpcard Data/Fax Modem User’s Guide and ReferenceCopyright How To Contact UsFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Features Data ModeFacsimile Mode Cellular ModeUnique Features 22bis Industry Standards32bis MNP 42bisMNP 2, 3, 27terHardware Installation Preparing for InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Before You Begin Enabling The TrumpcardUsing AT Commands Operating the TrumpcardMaking an Outgoing Call Tone or Pulse DiallingStoring a Number Re-Dialling the Last NumberConnection Messages Data Connect 1200TX/75RXFAX CarrierSetting Up for a Non-Error Correcting Connection Ending Your ConnectionSetting up for a Cellular Connection Receiving an Incoming CallModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference Modem Command Summary +MSModem Command Reference Re-execute Modem Command DescriptionsAnswer ATB0 Bn Set ITU-T or Bell ModeDn Dial ATB1ATDS=2 En Command Echo Fn Select Line Modulation 14400 only+Ms Select Line Modulation 28800 only Sub-parameter DefinitionsATH0 Hn Switch-Hook ControlVFC ATH1Olume IdentificationMn Speaker Control Nn Automode Detection On Return To The On-Line StateSn Read/Write S Registers Set Pulse Dial as DefaultQn Result Code Display ATQ0Vn Result Code Form Set Tone Dial as DefaultWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Yn Control Long Space Disconnect Zn ResetCn DCD Option Dn DTR Option Restore Factory ConfigurationNone Jn T elephone Jack Selection Gn Set Guard ToneKn DTE/Modem Flow Control Qn Communication Mode Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Ln Line TypeRn RTS/CTS Option Sn DSR OptionTn T est and Diagnostic AT&T7 View Configuration and User ProfilesAT&T6 AT&T8Yn Designate Default User Profile Wn Store User Profile\Gn Modem-to-Modem Flow Control Zn=x Store Phone Number\Bn T ransmit Break \Kn Break ControlAT\K3 AT\K1AT\K5 \Nn Operation Mode Control Cn Compression ControlReport Received Signal Level En Enable/Disable Line Quality MonitorReport Line Signal Quality Mn T ransmit Level Adjustment for Cellular Connection Kn MNP Extended ServicesHn Link Negotiation Speed @Mn Initial Cellular Power Level En Compromise EqualizerInit string Event Based Command Init string = NullModem S Registers Default Register SettingsModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S7 Wait For Carrier After Dial S5 Backspace CharacterS6 Wait S8 PauseS11 Dtmf T one Duration S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S12 Escape Code Guard TimeS25 Delay to DTR S18 Test TimerS24 Sleep Inactivity Timer S30 Inactivity TimerS33 Xoff Character S32 XON CharacterS36 Lapm Failure Control Range Default S37 Desired Telco Line SpeedS38 Delay Before Forced Disconnect S46 Protocol SelectionS48 V .42 Negotiation Action S86 Connection Failure Cause CodeS95 Extended Result Codes Class 1 Commands Facsimile CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Product Information Testing Modem MemoryROM Checksum Test