Ositech comm Trumpcard Data/Fax Modem manual Introduction

Page 11

Introduction

Section One

Introduction

Congratulations on your choice of an Ositech Trumpcard Data/Fax Modem! We believe you will find it a superior quality product that will meet or exceed your facsimile and data communication needs.

The Trumpcard Modem can be used with most standard communications and facsimile packages. Refer to the communications package documentation for instructions to set up and configure your communications software to take advantage of the Trumpcard Modem’s features.

This section lists the features of the Trumpcard Modem, briefly describes a number of industry standards, and provides basic instructions for getting started with your Trumpcard Modem.

Features

Industry Standards

Before You Begin Dialling

Communicating With the Trumpcard Modem

User’s Guide and Reference

1 - 1

Image 11
Contents User’s Guide and Reference Trumpcard Data/Fax ModemFTP How To Contact UsCopyright Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode FeaturesCellular Mode Facsimile ModeUnique Features 32bis Industry Standards22bis 27ter 42bisMNP 2, 3, MNPPreparing for Installation Hardware InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You BeginOperating the Trumpcard Using AT CommandsTone or Pulse Dialling Making an Outgoing CallConnection Messages Re-Dialling the Last NumberStoring a Number Carrier Connect 1200TX/75RXFAX DataEnding Your Connection Setting Up for a Non-Error Correcting ConnectionReceiving an Incoming Call Setting up for a Cellular ConnectionModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command SummaryModem Command Reference Answer Modem Command DescriptionsRe-execute ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0ATDS=2 Fn Select Line Modulation 14400 only En Command EchoSub-parameter Definitions +Ms Select Line Modulation 28800 onlyATH1 Hn Switch-Hook ControlVFC ATH0Mn Speaker Control IdentificationOlume On Return To The On-Line State Nn Automode DetectionATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S RegistersWn Connect Message Control Set Tone Dial as DefaultVn Result Code Form Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Cn DCD Option Zn ResetYn Control Long Space Disconnect None Restore Factory ConfigurationDn DTR Option Kn DTE/Modem Flow Control Gn Set Guard ToneJn T elephone Jack Selection Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication ModeSn DSR Option Rn RTS/CTS OptionTn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7Wn Store User Profile Yn Designate Default User Profile\Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow ControlAT\K5 AT\K1AT\K3 Cn Compression Control \Nn Operation Mode ControlReport Line Signal Quality En Enable/Disable Line Quality MonitorReport Received Signal Level Hn Link Negotiation Speed Kn MNP Extended ServicesMn T ransmit Level Adjustment for Cellular Connection En Compromise Equalizer @Mn Initial Cellular Power LevelInit string = Null Init string Event Based CommandModem Register Summary Default Register SettingsModem S Registers Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After DialS12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one DurationS30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTRS36 Lapm Failure Control S32 XON CharacterS33 Xoff Character S37 Desired Telco Line Speed Range DefaultS46 Protocol Selection S38 Delay Before Forced DisconnectS86 Connection Failure Cause Code S48 V .42 Negotiation ActionS95 Extended Result Codes Class 2 Commands Facsimile CommandsClass 1 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback ROM Checksum Test Testing Modem MemoryProduct Information