Ositech comm Trumpcard Data/Fax Modem manual Modem Command Reference

Page 67

				Modem Command Reference
S9 *		Carrier Detect Response Time			6
S10		Lost Carrier To Hang Up Delay			14
S11	*	DTMF Tone Duration			95
S12	*	Escape Code Guard Time			50
S13		Reserved			none
S14	*	Bit Mapped Options	**		138
S15		Reserved			none
S16		Bit Mapped Test Options **			0
S17		Reserved			none
S18	*	Test Timer			0
S19		Reserved			0
S20		Reserved			none
S21	*	Bit Mapped Options	**		4
S22	*	Bit Mapped Options	**		117
S23	*	Bit Mapped Options	**		55
S24		Sleep Inactivity Timer			10
S25	*	Delay To DTR			5
S27	*	Bit Mapped Options	**		74
S28		Bit Mapper Options			0
S29		Reserved			none
S30	*	Inactivity Timer			0
S31		Bit Mapper Options	**		194
S32		XON Flow Control Character			17
Register		Title			Default
S33		XOFF Flow Control Character			19
S34-S35		Reserved			none
S36	*	LAPM Failure Control			7
S37	*	Desired Telco Line Speed			0
S38	*	Delay Before Forced Disconnect			20
S39	*	Bit Mapped Options	**		3
S40		Bit Mapped Options (MNP)		**	105
S41		Bit Mapped Options (MNP)		**	03
S44		Unused			none
S46	*	Protocol Selection			138
S48	*	V.42 Negotiated Action			7
S86		Connection Failure Cause Code			0

User’s Guide and Reference

4 - 35

Image 67

Contents User’s Guide and Reference Trumpcard Data/Fax ModemCopyright How To Contact UsFTP Preface FCC Notice Regulations Governing the Use of Modems Page Vii Contents Modem Command Reference Page Introduction Data Mode FeaturesCellular Mode Facsimile ModeUnique Features 22bis Industry Standards32bis 27ter 42bisMNP 2, 3, MNPPreparing for Installation Hardware InstallationInstalling the Trumpcard Modem Pcmcia Modem Adapter connector is keyed to go in one way Line Interface Module Connection to Telephone Network Basic Modem Operation Enabling The Trumpcard Before You BeginOperating the Trumpcard Using AT CommandsTone or Pulse Dialling Making an Outgoing CallStoring a Number Re-Dialling the Last NumberConnection Messages Carrier Connect 1200TX/75RXFAX DataEnding Your Connection Setting Up for a Non-Error Correcting ConnectionReceiving an Incoming Call Setting up for a Cellular ConnectionModem Configurations for Cellular Operation Cellular Phone Configuration Cellular Call Status Section Four Trumpcard 14400/28800 Modem Modem Command Reference Modem Command Guidelines Modem Command Reference +MS Modem Command SummaryModem Command Reference Re-execute Modem Command DescriptionsAnswer ATB1 Bn Set ITU-T or Bell ModeDn Dial ATB0ATDS=2 Fn Select Line Modulation 14400 only En Command EchoSub-parameter Definitions +Ms Select Line Modulation 28800 onlyATH1 Hn Switch-Hook ControlVFC ATH0Olume IdentificationMn Speaker Control On Return To The On-Line State Nn Automode DetectionATQ0 Set Pulse Dial as DefaultQn Result Code Display Sn Read/Write S RegistersVn Result Code Form Set Tone Dial as DefaultWn Connect Message Control Xn Extended Result Codes Result Codes Q0, V1, Wn, S95 Carrier Connect Yn Control Long Space Disconnect Zn ResetCn DCD Option Dn DTR Option Restore Factory ConfigurationNone Jn T elephone Jack Selection Gn Set Guard ToneKn DTE/Modem Flow Control Ln Line Type Mn Communication ModePn Dial Pulse Ratio disabled for the U.S Qn Communication ModeSn DSR Option Rn RTS/CTS OptionTn T est and Diagnostic AT&T8 View Configuration and User ProfilesAT&T6 AT&T7Wn Store User Profile Yn Designate Default User Profile\Kn Break Control Zn=x Store Phone Number\Bn T ransmit Break \Gn Modem-to-Modem Flow ControlAT\K3 AT\K1AT\K5 Cn Compression Control \Nn Operation Mode ControlReport Received Signal Level En Enable/Disable Line Quality MonitorReport Line Signal Quality Mn T ransmit Level Adjustment for Cellular Connection Kn MNP Extended ServicesHn Link Negotiation Speed En Compromise Equalizer @Mn Initial Cellular Power LevelInit string = Null Init string Event Based CommandModem S Registers Default Register SettingsModem Register Summary Modem Command Reference S95 Extended Result Codes Register Descriptions S8 Pause S5 Backspace CharacterS6 Wait S7 Wait For Carrier After DialS12 Escape Code Guard Time S10 Lost Carrier To Hang Up DelayS9 Carrier Detect Response Time S11 Dtmf T one DurationS30 Inactivity Timer S18 Test TimerS24 Sleep Inactivity Timer S25 Delay to DTRS33 Xoff Character S32 XON CharacterS36 Lapm Failure Control S37 Desired Telco Line Speed Range DefaultS46 Protocol Selection S38 Delay Before Forced DisconnectS86 Connection Failure Cause Code S48 V .42 Negotiation ActionS95 Extended Result Codes Class 1 Commands Facsimile CommandsClass 2 Commands Modem Test Procedures Local Modem Self-Test Local Analog Loopback Local Analog Loopback with Self- Generated Pattern Remote Digital Loopback Remote Digital Loopback with Self- Generated Pattern Local Digital Loopback Product Information Testing Modem MemoryROM Checksum Test