PSC 315 manual Reboot Mobile Unit

Page 63

Error Message Resolution Guide

Message

Reason

Solution

Reference Tech Note

Connection ERROR.\nREBOOT

Could not Connect.

MOBILE UNIT;

 

Disconnect ERROR.\nREBOOT

Could not Disconnect.

MOBILE UNIT;

 

RF Send ERROR.\nREBOOT MOBILE Could not Send. UNIT;

RF Receive ERROR.\nREBOOT

Could not Receive.

MOBILE UNIT;

 

RF Check ERROR.\nREBOOT

Could not run the RF Survey.

MOBILE UNIT;

 

RF Timeout ERROR.\nREBOOT

Have been trying to contact the

MOBILE UNIT;

host for the radio timeout period (2

 

minutes default).

REBOOT MOBILE UNIT;

Reboot the Mobile Unit do to loss

 

of connection.

Verify that your Network settings are

T1113, T1114, T1161,

correct and you are in the correct mode

T1171, T1187 and

using the correct Port.

T1194

Verify that your Network settings are

T1113, T1114, T1161,

correct and you are in the correct mode

T1171, T1187 and

using the correct Port.

T1194

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

Most likely a range, access point, radio,

T1113, T1114, T1161,

host or network issue. Troubleshoot the

T1171, T1187 and

customer’s environment.

T1194

Retry (Y/N)?;

Try again.

Try to send or receive again, or perhaps

---

 

 

ensure that the printer is cabled to the

 

 

 

Mobile Unit and is on.

 

Supported Equipment Manual May, 2006

4-3

Image 63
Contents Supported Equipment Manual Copyright 1996 2006 by Connect, Inc TrademarksProduction Introduction Terminal SetupChapter Keypad Configuration Chapter Error Message Resolution GuideThis page is intentionally blank Picture DescriptionVersion of Bios Setup RequirementsAccessories BiosRelease Notes Patch version a Downloading from the WEB Running Setup from a Download File Terminal SetupInstallation Installation Menu Bar Running the ManagerToolbar Configuring the ManagerSetting the Emulation Quick StartSetting the Servers Setting Terminal Operations Saving the Configuration Setting Terminal ModelSetting Airloader Auto-Configuration Terminal Setup Downloading Files To Terminal Booting the Terminal Starting a Telnet Session Recoverable ErrorStandard Setup Setup Using Twin Client ManagerVT Settings Quadrant Mode Settings Quadrant Mode Key Click Quadrant Mode Terminal Setup Using Twin Client Menus Edit Mobile Unit IPEdit Server/Host IPs Run Client Emulator Switch Client ModesEdit License Key Run Site SurveyAuthorizing PowerNet Authorized Terminals Adding Licenses Transferring Licenses Listing Airloader Auto-Configuration Software ManagementEnabling Automatic Downloads Synchronizing Configuration Files Synchronizing Program FilesAutomatic IP Address Assignment Creating New Groups Terminal Setup Software Management Reassigning Terminals Setting the SegmentSetting Force Reload Setting the Default Terminal GroupMobile Device Manager MDM Features Select Terminal Messenger from the Tools menu Software Management Terminal Setup Software Management Terminal Setup Software Management Terminal Setup Common Problems with RF Monitor Terminal Setup Manual Download of Configuration Files This page is intentionally blank Keypad Figures Keypad ConfigurationFN1 FN2 ESC 5250 Vterm Keypad TableAlt PA1 This page is intentionally blank Decimal not Valid Entry TOO LongAlphabetic only Minus not ValidScan not Allowed Unrecoverable ErrorInvalid KEY Must Clear FieldMobile Unit Reboot Mobile UnitWaiting to Send Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Place in Cradle OUT of Range of BaseConnect Serial Cable Remove Serial CableAcquiring Cradle BUS Remove from CradleMessage Reason Solution Reference Tech Note Name Server Message Reason Solution Reference Tech Note Host Entry Emulation Setup Miscellaneous Setup Login OptionsTest Options OFF Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Null Setup