PSC 315 manual Message Reason Solution Reference Tech Note

Page 67

Error Message Resolution Guide

Message

Reason

Solution

Reference Tech Note

Font Loading Error;

Could not load the font.

Ensure that the font is available to load.

---

Printer Not Ready\nPress R to

Can not print.

Check cable, battery, communication

---

Retry\nC to Cancel Print;

 

settings and paper in the printer.

 

Mobile Unit in\nDemonstration

Running in demo mode.

Purchase a license from Connect.

---

Mode\nfor TwinClient;

 

 

 

Connected to Host;

Successful connection to the target Advisory message.

---

 

Host.

 

 

Telnet Mode not\nsupported on\nthis

This Mobile Unit must be used with

Order a Connect Server.

---

Mobile Unit;

a Connect Server.

 

 

Telnet Setup files\nnot found.

Customer specific configuration

Load the configuration files into the Mobile

---

Reload\nfiles then switch;

files are missing.

Unit from Twin Client Manager.

 

Switched Client to\nTelnet Direct Mode; Mobile Unit running in Telnet mode

Advisory message.

---

 

direct to the target Host.

 

 

Switched Client to\nServer Based

Mobile Unit running through a

Advisory message.

---

Mode;

Connect server in Server mode

 

 

 

usually at port 1800.

 

 

Port 23 is only\nallowed in Telnet Mode;

Can not set the port to 23 in Server Advisory message.

---

mode. Port 23 is the standard

 

Telnet port.

 

Not Enough Memory\nTo Run;

Mobile Unit does not have the

Expand the Mobile Unit memory.

---

 

capacity to run the program do to

 

 

 

memory restrictions.

 

 

Press any key;

Press a key to continue.

Advisory message.

---

Supported Equipment Manual May, 2006

4-7

Image 67
Contents Supported Equipment Manual Trademarks Copyright 1996 2006 by Connect, IncProduction Introduction Terminal SetupChapter Keypad Configuration Chapter Error Message Resolution GuideThis page is intentionally blank Picture DescriptionVersion of Bios Setup RequirementsAccessories BiosRelease Notes Patch version a Downloading from the WEB Running Setup from a Download File Terminal SetupInstallation Installation Menu Bar Running the ManagerToolbar Configuring the ManagerSetting the Emulation Quick StartSetting the Servers Setting Terminal Operations Saving the Configuration Setting Terminal ModelSetting Airloader Auto-Configuration Terminal Setup Downloading Files To Terminal Booting the Terminal Starting a Telnet Session Recoverable ErrorSetup Using Twin Client Manager Standard SetupVT Settings Quadrant Mode Settings Quadrant Mode Key Click Quadrant Mode Edit Mobile Unit IP Terminal Setup Using Twin Client MenusEdit Server/Host IPs Run Client Emulator Switch Client ModesEdit License Key Run Site SurveyAuthorizing PowerNet Authorized Terminals Adding Licenses Transferring Licenses Listing Software Management Airloader Auto-ConfigurationEnabling Automatic Downloads Synchronizing Program Files Synchronizing Configuration FilesAutomatic IP Address Assignment Creating New Groups Terminal Setup Software Management Reassigning Terminals Setting the SegmentSetting Force Reload Setting the Default Terminal GroupMobile Device Manager MDM Features Select Terminal Messenger from the Tools menu Software Management Terminal Setup Software Management Terminal Setup Software Management Terminal Setup Common Problems with RF Monitor Terminal Setup Manual Download of Configuration Files This page is intentionally blank Keypad Figures Keypad ConfigurationFN1 FN2 ESC 5250 Vterm Keypad TableAlt PA1 This page is intentionally blank Decimal not Valid Entry TOO LongAlphabetic only Minus not ValidScan not Allowed Unrecoverable ErrorInvalid KEY Must Clear FieldMobile Unit Reboot Mobile UnitWaiting to Send Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Place in Cradle OUT of Range of BaseConnect Serial Cable Remove Serial CableAcquiring Cradle BUS Remove from CradleMessage Reason Solution Reference Tech Note Name Server Message Reason Solution Reference Tech Note Host Entry Emulation Setup Login Options Miscellaneous SetupTest Options OFF Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Message Reason Solution Reference Tech Note Null Setup