Printek 850 Series manual Load/Feed

Page 31

D A I L Y O P E R A T I O N

LOAD/FEED

This button performs a number of different form

 

feeding functions. The printer will automatically

 

select the correct function to perform based upon

 

the current position of the form.

 

LOAD:

 

∙ Loads the form that is presently selected.

 

If the selected form is already recognized as

 

“loaded” in the tractors, the printer will

 

advance the form to the print position.

 

If the selected form is not currently

 

considered to be loaded in the tractors

 

(display shows <Not Loaded>), this

 

button will change the status of this form to

 

“loaded”.

 

FORM FEED:

 

∙ If a form is currently loaded and perhaps

 

partially printed, this button will advance the

 

bottom of the current form to the tear bar so

 

that it may be torn off.

 

∙ If a form has already been advanced to the

 

tear bar, this button will advance the next

 

form to the tear bar.

UNLOAD/CHANGE

This button is used to access up to ten different

 

forms, which have been previously configured

 

with the Setup menus (see the chapter on

 

PRINTER CONFIGURATION” for more

 

information).

 

When this button is pressed, one of two functions

 

will be performed.

2 3

Image 31
Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Test Menu Introduction To SetupForms Menu Interface MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O RS-232C Serial Interface Interface Set UpParallel Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ Left/Right ⎯0.30→ Down/UpDown/Up 0.08 ↓ Common Error ConditionsCheck Paper Too Much Paper to Unload No Paper to LoadSelected Form is not Loaded Ribbon Lid Open Other ErrorsIntroduction To Setup Printer ConfigurationSetup Buttons Form Entering SetupEntering Setup Menus Using the Menu ButtonExiting Menus Saving Changes No Changes Using the Submenu ButtonUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Exiting SetupForms Menu Items Forms MenuForm Name Tractor Path Rear FormBottom Margin 0 Lines Lines/InchForm Length 66 Lines Top Margin 0 LinesLeft Margin Column Characters/Inc hRight Margin Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalEntering the Interface Menu Interface MenuSerial Auto LF Off RS-232C Serial Interface ItemsInterface Menu Serial Emulation Epson Auto CR OnCharacters Control Host FF at TOF NoMinimum Buffer No Parity None Baud RateData Bits Stop BitsBusy Polarity Low DTR Power On/OffXON/XOFF Off Parallel/LAN Interface Items ETX/ACK OffParallel/LAN Emulation Epson LAN Setup OffIP Address Auto Subnet Mask IP AddressIP Gateway Auto LF Off Max Form Allowed Options MenuPaper Out Fault Finish Auto-Scroll 1 Second DelayTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255User Language English Top Oversized OffSize 8192 Characters Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting Security Menu Advanced Setup FeaturesALIGN/ITEM Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when