Printek 850 Series manual No Paper to Load, Too Much Paper to Unload, Selected Form is not Loaded

Page 40

D A I L Y O P E R A T I O N

If the error is caused by a paper jam, remove the jammed form. If the form remaining in the tractors has tears along the top edge, remove it from the tractors, tear it off, and place the next form in the tractors.

If the error is caused by running out of paper, simply load a form as previously described.

Finally, place the printer back on line by pressing the ONLINE button. This will automatically load the new form and begin printing. Depending upon how the printer has been set up, the printer may start printing where it left off or it may start at the beginning of the page where the error occurred and reprint the entire page. See “Paper Out Fault Action” on page 54 for more information.

No Paper to Load

This error occurs when the LOAD/FEED button has been pressed and there is no paper or form in the tractors. Place paper in the tractors and press LOAD/FEED again.

Too Much Paper to Unload

This error occurs when the UNLOAD/CHANGE button has been pressed and there is paper present too far beyond the tear bar. This error serves as a warning that you may be putting forms that have already been printed on back into the printer. Tear off any printed forms past the tear bar and press UNLOAD/CHANGE again. This error also occurs if the LOAD/FEED button has been pressed and the current form cannot be unloaded.

Selected Form is not Loaded

This error occurs when ONLINE has been pressed and the currently selected form is displaying <Not Loaded>. Either press LOAD/FEED to load the selected form or select a different form, then press LOAD/FEED and then press ONLINE.

3 2

Image 40
Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Introduction To Setup Forms MenuInterface Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Installation Getting StartedParallel I/O Serial I/O RS-232C Serial Interface Interface Set UpParallel Interface Ethernet 10/100BaseT Installing The Ribbon Cartridge Why Use Only Printek Brand RibbonsT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D Loading Paper PrintMaster 850/850si Single Tractor ModelInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Daily Operation IntroductionControl Panel Features LCD Display and Online Status Indicator LEDDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Hidden Under LID Buttons Setup UnloadSelecting and Loading Forms Selecting a Form Already Loaded in the Tractors Loading a New or Different Form In the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ Down/Up Left/Right ⎯0.30→Down/Up 0.08 ↓ Common Error ConditionsCheck Paper Too Much Paper to Unload No Paper to LoadSelected Form is not Loaded Other Errors Ribbon Lid OpenIntroduction To Setup Printer ConfigurationSetup Buttons Entering Setup Entering Setup MenusUsing the Menu Button FormUsing the Submenu Button Using the ALIGN/ITEM and UP/DOWN Arrow ButtonsExiting Setup Exiting Menus Saving Changes No ChangesForms Menu Items Forms MenuForm Name Form Tractor Path RearLines/Inch Form Length 66 LinesTop Margin 0 Lines Bottom Margin 0 LinesLeft Margin Column Characters/Inc hRight Margin Font Epson FX FD Draft Speed NormalImpact Force Normal LanguageZero Normal Unidirectional NoEntering the Interface Menu Interface MenuSerial RS-232C Serial Interface Items Interface Menu Serial Emulation EpsonAuto CR On Auto LF OffCharacters Control Host FF at TOF NoMinimum Buffer No Baud Rate Data BitsStop Bits Parity NoneBusy Polarity Low DTR Power On/OffXON/XOFF Off Parallel/LAN Interface Items ETX/ACK OffParallel/LAN Emulation Epson LAN Setup OffIP Address Auto Subnet Mask IP AddressIP Gateway Auto LF Off Options Menu Max Form AllowedPaper Out Fault Finish Auto-Scroll 1 Second DelayTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Char. To Ignore 255 Top of Barcode OffUser Language English Top Oversized OffSize 8192 Characters Truncate Lines No Bottom Slew FastTest Mode Off Print MenusForm Construction and Layout Tips Form ConstructionForm Layout Considerations E C I F Y I N G F O R M S Maintenance Troubleshooting Error MessagesPreventive Maintenance Obtaining ServiceI N T E N a N C E a N D Troubleshooting Security Menu Advanced Setup FeaturesALIGN/ITEM Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Copying Setup To ModuleI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Control Code Escape Sequence Summaries Genicom 3840 and 3410 EmulationAnsi X3.64 Emulation Epson FX Emulation ESC * m n1 n2 dataESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S Specifications 60 to 240 dpi horizontally x 72 dpi vertically6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Glossary of Terms AsciiLCD Online Refers to the state of the printer when