Printek 850 Series manual I N G T H E O P T I O N a L S E T U P M O D U L E

Page 85

U S I N G T H E O P T I O N A L S E T U P M O D U L E

in step 9 press the LOAD button. Depending upon what was repaired in the printer, the Setup information in the printer’s memory may not have been changed. In this case the printer will power up normally and no message will be displayed.

Using the Setup Module to

Copy Setup Data From One Printer to Another

This use of the Setup Module is beneficial when installing or updating several printers that need to be configured exactly the same. To do this, you will need to perform the installation procedure once for each printer.

First, install the Setup Module on the printer where the Setup data is to be copied from. If the printer determines that steps 8 and 9 are required, choose “Copy to Module” in step 9 and allow the printer’s power up procedures to complete. If any additional changes need to be made to the configuration of this printer, enter Setup and make them before removing the Setup Module. Any changes made will automatically be stored both in the printer’s internal memory and the Setup Module.

You may now power off the printer and remove the Setup Module. Remember to reconnect the serial cable if one was attached.

Now perform the installation procedure on each of the printers that are to be configured the same as the first. In step 9 be sure to press the LOAD button to copy data to the printer. After the Setup Module is removed, remember to reconnect the serial cable if one was attached.

Note: Setup modules for Printek FormsMaster 8000 Series printers and PrintMaster 850 Series printers are not interchangeable. Data backup will not take place if the modules are used on the wrong printer.

7 7

Image 85

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Forms Menu Introduction To SetupInterface Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O RS-232C Serial Interface Interface Set UpParallel Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ Left/Right ⎯0.30→ Down/UpDown/Up 0.08 ↓ Common Error ConditionsCheck Paper Too Much Paper to Unload No Paper to LoadSelected Form is not Loaded Ribbon Lid Open Other ErrorsIntroduction To Setup Printer ConfigurationSetup Buttons Entering Setup Menus Entering SetupUsing the Menu Button FormUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Using the Submenu ButtonExiting Setup Exiting Menus Saving Changes No ChangesForms Menu Items Forms MenuForm Name Tractor Path Rear FormForm Length 66 Lines Lines/InchTop Margin 0 Lines Bottom Margin 0 LinesLeft Margin Column Characters/Inc hRight Margin Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalEntering the Interface Menu Interface MenuSerial Interface Menu Serial Emulation Epson RS-232C Serial Interface ItemsAuto CR On Auto LF OffCharacters Control Host FF at TOF NoMinimum Buffer No Data Bits Baud RateStop Bits Parity NoneBusy Polarity Low DTR Power On/OffXON/XOFF Off Parallel/LAN Interface Items ETX/ACK OffParallel/LAN Emulation Epson LAN Setup OffIP Address Auto Subnet Mask IP AddressIP Gateway Auto LF Off Max Form Allowed Options MenuPaper Out Fault Finish Auto-Scroll 1 Second DelayTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255User Language English Top Oversized OffSize 8192 Characters Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting Security Menu Advanced Setup FeaturesALIGN/ITEM Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when