Printek 850 Series manual Auto-Scroll 1 Second Delay, Tear-Off 0.00 Inches, Paper Out Fault Finish

Page 62

S P E C I F Y I N G F O R M S

Automatic Scroll Delay

Auto-Scroll 1 Second Delay

Possible Values: Off, 1* to 15 Second Delay

This item sets the number of seconds to delay before scrolling the top of form to the tear bar when the printer is idle (no additional data received since the last print operation) and a form boundary (bottom of the form according to the Form Length setting for the current form) has been reached. If printing finishes and the form boundary has not been reached, take the printer off line and the LOAD/FEED button may be used to advance the form to the tear bar. This item may also be used to disable Auto-Scroll by setting the value to Off. When disabled, the LOAD/FEED button must always be used to advance the form to the tear bar.

Tear-Off Distance

Possible Values: 0.00* … 9.99 Inches

Tear-Off 0.00 Inches

This item sets the additional distance the paper will advance when scrolling to the tear bar. This allows the printer to be placed under a slot in a counter and have the tear-off positioned at the counter surface. Leave the distance set to 0.00 Inches to disable this feature. To set the value, use the UP/DOWN ARROW buttons to change the value. Holding the buttons will cause the value to change rapidly. The paper will move accordingly to allow verification of the setting. Note that the setup Menus will not terminate when closing the lid while in this mode.

Paper Out Fault Action

Possible Values: Finish Page*

Reprint Page

Break Page

Paper Out

Fault

Finish Page

5 4

Image 62

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Interface Menu Introduction To SetupForms Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Installation Getting StartedParallel I/O Serial I/O Parallel Interface Interface Set UpRS-232C Serial Interface Ethernet 10/100BaseT Installing The Ribbon Cartridge Why Use Only Printek Brand RibbonsT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D Loading Paper PrintMaster 850/850si Single Tractor ModelInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Daily Operation IntroductionControl Panel Features LCD Display and Online Status Indicator LEDDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Hidden Under LID Buttons Setup UnloadSelecting and Loading Forms Selecting a Form Already Loaded in the Tractors Loading a New or Different Form In the TractorsEjecting and Tearing Off a Form Tearing off a Form Left/Right ←0.00→ Aligning PrintAligning Print On Invoices Down/Up Left/Right ⎯0.30→Check Paper Common Error ConditionsDown/Up 0.08 ↓ Selected Form is not Loaded No Paper to LoadToo Much Paper to Unload Other Errors Ribbon Lid OpenSetup Buttons Printer ConfigurationIntroduction To Setup Using the Menu Button Entering SetupEntering Setup Menus FormExiting Setup Using the Submenu ButtonUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Exiting Menus Saving Changes No ChangesForm Name Forms MenuForms Menu Items Form Tractor Path RearTop Margin 0 Lines Lines/InchForm Length 66 Lines Bottom Margin 0 LinesRight Margin Characters/Inc hLeft Margin Column Font Epson FX FD Draft Speed NormalImpact Force Normal LanguageZero Normal Unidirectional NoSerial Interface MenuEntering the Interface Menu Auto CR On RS-232C Serial Interface ItemsInterface Menu Serial Emulation Epson Auto LF OffMinimum Buffer No Host FF at TOF NoCharacters Control Stop Bits Baud RateData Bits Parity NoneXON/XOFF Off DTR Power On/OffBusy Polarity Low Parallel/LAN ETX/ACK OffParallel/LAN Interface Items IP Address Auto LAN Setup OffEmulation Epson IP Gateway IP Address Subnet Mask Auto LF Off Options Menu Max Form AllowedTear-Off 0.00 Inches Auto-Scroll 1 Second DelayPaper Out Fault Finish Cannot Reprint Page Too Large will be displayed, Char. To Ignore 255 Top of Barcode OffSize 8192 Characters Top Oversized OffUser Language English Truncate Lines No Bottom Slew FastTest Mode Off Print MenusForm Construction and Layout Tips Form ConstructionForm Layout Considerations E C I F Y I N G F O R M S Maintenance Troubleshooting Error MessagesPreventive Maintenance Obtaining ServiceI N T E N a N C E a N D Troubleshooting ALIGN/ITEM Edit Allowed Advanced Setup FeaturesSecurity Menu Options Menu Edit Allowed Forms Menu Edit AllowedInterface Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Copying Setup To ModuleI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Control Code Escape Sequence Summaries Genicom 3840 and 3410 EmulationAnsi X3.64 Emulation Epson FX Emulation ESC * m n1 n2 dataESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S Specifications 60 to 240 dpi horizontally x 72 dpi vertically6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Glossary of Terms AsciiLCD Online Refers to the state of the printer when