Printek 850 Series manual Printer Configuration, Introduction To Setup, Setup Buttons

Page 42

PRINTER CONFIGURATION

Introduction To Setup

The PrintMaster 850 Series printers feature simple, easy to use menus for setting the various operating parameters for the printer. The parameters available in these menus usually only need to be set one time, either when the printer is first installed or perhaps when a new form is to be used. These values are stored in nonvolatile memory, which means that they will remain set even if the printer is turned off. Please note that, in an effort to minimize the total number of buttons and provide an uncluttered control panel, most buttons on the PrintMaster 850 Series printers are “context- sensitive”, i.e., their specific function is dependent on the present state of the printer or the menu level you happen to be in. For example, the Unload/Change button is used to unload forms or change the loaded form in the printer, depending on whether a form is loaded already. When in the Menu system with the Front Lid open, this same physical button serves as a “Down Arrow” button, allowing you to modify the settings of various printer parameters. The following sections give detailed descriptions of the buttons and the different functions they perform depending on the context. Following this introduction are complete, detailed descriptions of each menu item.

Setup Buttons

For your convenience, the MENU button and the other buttons used while in the Setup mode are labeled in yellow on the control panel. Once in Setup, these buttons are the MENU, SUBMENU, ALIGN/ITEM, and UP/DOWN ARROW buttons. The ONLINE indicator will flash yellow whenever the

34

Image 42
Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Interface Menu Introduction To SetupForms Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Installation Getting StartedParallel I/O Serial I/O Interface Set Up RS-232C Serial InterfaceParallel Interface Ethernet 10/100BaseT Installing The Ribbon Cartridge Why Use Only Printek Brand RibbonsT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D Loading Paper PrintMaster 850/850si Single Tractor ModelInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Daily Operation IntroductionControl Panel Features LCD Display and Online Status Indicator LEDDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Hidden Under LID Buttons Setup UnloadSelecting and Loading Forms Selecting a Form Already Loaded in the Tractors Loading a New or Different Form In the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Down/Up Left/Right ⎯0.30→Common Error Conditions Down/Up 0.08 ↓Check Paper No Paper to Load Too Much Paper to UnloadSelected Form is not Loaded Other Errors Ribbon Lid OpenPrinter Configuration Introduction To SetupSetup Buttons Using the Menu Button Entering SetupEntering Setup Menus FormExiting Setup Using the Submenu ButtonUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Exiting Menus Saving Changes No ChangesForms Menu Forms Menu ItemsForm Name Form Tractor Path RearTop Margin 0 Lines Lines/InchForm Length 66 Lines Bottom Margin 0 LinesCharacters/Inc h Left Margin ColumnRight Margin Font Epson FX FD Draft Speed NormalImpact Force Normal LanguageZero Normal Unidirectional NoInterface Menu Entering the Interface MenuSerial Auto CR On RS-232C Serial Interface ItemsInterface Menu Serial Emulation Epson Auto LF OffHost FF at TOF No Characters ControlMinimum Buffer No Stop Bits Baud RateData Bits Parity NoneDTR Power On/Off Busy Polarity LowXON/XOFF Off ETX/ACK Off Parallel/LAN Interface ItemsParallel/LAN LAN Setup Off Emulation EpsonIP Address Auto IP Address Subnet MaskIP Gateway Auto LF Off Options Menu Max Form AllowedAuto-Scroll 1 Second Delay Paper Out Fault FinishTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Char. To Ignore 255 Top of Barcode OffTop Oversized Off User Language EnglishSize 8192 Characters Truncate Lines No Bottom Slew FastTest Mode Off Print MenusForm Construction and Layout Tips Form ConstructionForm Layout Considerations E C I F Y I N G F O R M S Maintenance Troubleshooting Error MessagesPreventive Maintenance Obtaining ServiceI N T E N a N C E a N D Troubleshooting Advanced Setup Features Security MenuALIGN/ITEM Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Copying Setup To ModuleI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Control Code Escape Sequence Summaries Genicom 3840 and 3410 EmulationAnsi X3.64 Emulation Epson FX Emulation ESC * m n1 n2 dataESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S Specifications 60 to 240 dpi horizontally x 72 dpi vertically6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Glossary of Terms AsciiLCD Online Refers to the state of the printer when