Printek 850 Series manual Entering the Interface Menu, Serial

Page 52

S P E C I F Y I N G F O R M S

Interface Menu

The Interface Menu may contain several submenus. These submenus are for setting up items pertaining to the hardware interfaces such as the serial and parallel ports.

In addition to the standard parallel interface and the RS-232C serial interface, which are furnished with the printer, 10/100BaseT Ethernet may also be installed. The Setup items for each interface are described in one of the following sections.

RS-232C Serial Interface on page 45

Parallel/LAN Interface on page 49

Entering the Interface Menu

To Enter the Interface Menu, enter Setup and press the MENU button until INTERFACE MENU is displayed on the top line as shown below.

INTERFACE MENU

Serial

The SUBMENU options for the INTERFACE MENU always include the Serial and Parallel/LAN ports. To select the desired interface, press the SUBMENU button until that interface is displayed on the bottom line. Note that when the Lan Setup option under the Parallel/LAN item list is set to On, the serial Interface is not available and will not appear in the Interface Menu. Next press the ALIGN/ITEM button to begin displaying the items associated with that interface. Each interface and the items, which pertain to that interface, are listed on the following pages. Note that many items are the same for more than one interface since the computer attached to that interface may have different requirements for each of those items.

The factory default values are indicated with an asterisk (*) in this manual (the asterisk does not appear on the printer’s display).

4 4

Image 52

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Introduction To Setup Forms MenuInterface Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Installation Getting StartedParallel I/O Serial I/O RS-232C Serial Interface Interface Set UpParallel Interface Ethernet 10/100BaseT Installing The Ribbon Cartridge Why Use Only Printek Brand RibbonsT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D Loading Paper PrintMaster 850/850si Single Tractor ModelInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Daily Operation IntroductionControl Panel Features LCD Display and Online Status Indicator LEDDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Hidden Under LID Buttons Setup UnloadSelecting and Loading Forms Selecting a Form Already Loaded in the Tractors Loading a New or Different Form In the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ Down/Up Left/Right ⎯0.30→Down/Up 0.08 ↓ Common Error ConditionsCheck Paper Too Much Paper to Unload No Paper to LoadSelected Form is not Loaded Other Errors Ribbon Lid OpenIntroduction To Setup Printer ConfigurationSetup Buttons Entering Setup Entering Setup MenusUsing the Menu Button FormUsing the Submenu Button Using the ALIGN/ITEM and UP/DOWN Arrow ButtonsExiting Setup Exiting Menus Saving Changes No ChangesForms Menu Items Forms MenuForm Name Form Tractor Path RearLines/Inch Form Length 66 LinesTop Margin 0 Lines Bottom Margin 0 LinesLeft Margin Column Characters/Inc hRight Margin Font Epson FX FD Draft Speed NormalImpact Force Normal LanguageZero Normal Unidirectional NoEntering the Interface Menu Interface MenuSerial RS-232C Serial Interface Items Interface Menu Serial Emulation EpsonAuto CR On Auto LF OffCharacters Control Host FF at TOF NoMinimum Buffer No Baud Rate Data BitsStop Bits Parity NoneBusy Polarity Low DTR Power On/OffXON/XOFF Off Parallel/LAN Interface Items ETX/ACK OffParallel/LAN Emulation Epson LAN Setup OffIP Address Auto Subnet Mask IP AddressIP Gateway Auto LF Off Options Menu Max Form AllowedPaper Out Fault Finish Auto-Scroll 1 Second DelayTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Char. To Ignore 255 Top of Barcode OffUser Language English Top Oversized OffSize 8192 Characters Truncate Lines No Bottom Slew FastTest Mode Off Print MenusForm Construction and Layout Tips Form ConstructionForm Layout Considerations E C I F Y I N G F O R M S Maintenance Troubleshooting Error MessagesPreventive Maintenance Obtaining ServiceI N T E N a N C E a N D Troubleshooting Security Menu Advanced Setup FeaturesALIGN/ITEM Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module Initializing Setup Module New Setup Module DetectedCopying Setup to Printer Copying Setup To ModuleI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Control Code Escape Sequence Summaries Genicom 3840 and 3410 EmulationAnsi X3.64 Emulation Epson FX Emulation ESC * m n1 n2 dataESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Simple TTY Emulation Printek EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S Specifications 60 to 240 dpi horizontally x 72 dpi vertically6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Glossary of Terms AsciiLCD Online Refers to the state of the printer when