Printek 850 Series Lines/Inch, Form Length 66 Lines, Top Margin 0 Lines, Bottom Margin 0 Lines

Page 47

S P E C I F Y I N G F O R M S

Lines Per Inch

Possible Values: 6*, 8

Lines/Inch

6

This item sets the line pitch to 6 or 8 lines per inch (LPI).

Form Length

Possible Values: 1 … 66* … 227 Lines

Form Length 66 Lines

This item sets the form length in lines at the current line pitch (LPI). For example: for an eleven-inch form, enter 66 if you are using six lines per inch or 88 if you are using eight lines per inch.

Top Margin

Possible Values: 0* … 226 Lines

Top Margin 0 Lines

This item sets the top margin in lines. Setting a top margin will reduce the size of the printable area of the page by the number of lines set. Printing will not be allowed above the top margin.

Note: In most cases changing where printing begins on a form should be accomplished with ALIGN/ITEM rather than with a top margin. Adding a top margin may cause some programs to print the first form correctly and then print following forms too far down the page if the program sending the data does not require the margin.

Bottom Margin

Bottom Margin 0 Lines

3 9

Image 47
Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Test Menu Introduction To SetupForms Menu Interface MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O Parallel Interface Interface Set UpRS-232C Serial Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Left/Right ←0.00→ Aligning PrintAligning Print On Invoices Left/Right ⎯0.30→ Down/UpCheck Paper Common Error ConditionsDown/Up 0.08 ↓ Selected Form is not Loaded No Paper to LoadToo Much Paper to Unload Ribbon Lid Open Other ErrorsSetup Buttons Printer ConfigurationIntroduction To Setup Form Entering SetupEntering Setup Menus Using the Menu ButtonExiting Menus Saving Changes No Changes Using the Submenu ButtonUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Exiting SetupForm Name Forms MenuForms Menu Items Tractor Path Rear FormBottom Margin 0 Lines Lines/InchForm Length 66 Lines Top Margin 0 LinesRight Margin Characters/Inc hLeft Margin Column Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalSerial Interface MenuEntering the Interface Menu Auto LF Off RS-232C Serial Interface ItemsInterface Menu Serial Emulation Epson Auto CR OnMinimum Buffer No Host FF at TOF NoCharacters Control Parity None Baud RateData Bits Stop BitsXON/XOFF Off DTR Power On/OffBusy Polarity Low Parallel/LAN ETX/ACK OffParallel/LAN Interface Items IP Address Auto LAN Setup OffEmulation Epson IP Gateway IP AddressSubnet Mask Auto LF Off Max Form Allowed Options MenuTear-Off 0.00 Inches Auto-Scroll 1 Second DelayPaper Out Fault Finish Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255Size 8192 Characters Top Oversized OffUser Language English Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting ALIGN/ITEM Edit Allowed Advanced Setup FeaturesSecurity Menu Options Menu Edit Allowed Forms Menu Edit AllowedInterface Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when