Printek 850 Series manual Informing the Printer That the New Form is Loaded

Page 21

G E T T I N G S T A R T E D

4.The form should be face down as shown in the picture. Place the left edge of the new form in the left tractor with the holes aligned with tractor pins. Make sure that the top edge of the form does not extend above the top of the tractors.

5.Close the left tractor door.

6.Now position the paper in the right tractor in the same fashion. If necessary, the position of the right tractor may be adjusted. To do so, move the lever on the side of the tractor back to unlock the tractor and slide the tractor sideways on the shafts.

7.After the paper is placed in the tractor and the door is closed, position the tractor far enough to the right so that there is no buckle in the paper between the tractors, but not so tight that the holes in the paper are distorted. Lock the tractor in place by returning the lever to the forward position.

Informing the Printer That the New Form is Loaded

1.Press the LOAD/FEED button. The display will now show that the new form has been “loaded”.

2.Close the paper door.

3.Make sure the correct form to be positioned for printing is selected and press either the LOAD/FEED button or the ONLINE button. The LOAD/FEED button will position the form for printing but will not place the printer on line. The ONLINE button will both position the form and place the printer on line.

1 3

Image 21

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Forms Menu Introduction To SetupInterface Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O Interface Set Up RS-232C Serial InterfaceParallel Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Left/Right ⎯0.30→ Down/UpCommon Error Conditions Down/Up 0.08 ↓Check Paper No Paper to Load Too Much Paper to UnloadSelected Form is not Loaded Ribbon Lid Open Other ErrorsPrinter Configuration Introduction To SetupSetup Buttons Entering Setup Menus Entering SetupUsing the Menu Button FormUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Using the Submenu ButtonExiting Setup Exiting Menus Saving Changes No ChangesForms Menu Forms Menu ItemsForm Name Tractor Path Rear FormForm Length 66 Lines Lines/InchTop Margin 0 Lines Bottom Margin 0 LinesCharacters/Inc h Left Margin ColumnRight Margin Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalInterface Menu Entering the Interface MenuSerial Interface Menu Serial Emulation Epson RS-232C Serial Interface ItemsAuto CR On Auto LF OffHost FF at TOF No Characters ControlMinimum Buffer No Data Bits Baud RateStop Bits Parity NoneDTR Power On/Off Busy Polarity LowXON/XOFF Off ETX/ACK Off Parallel/LAN Interface ItemsParallel/LAN LAN Setup Off Emulation EpsonIP Address Auto IP Address Subnet MaskIP Gateway Auto LF Off Max Form Allowed Options MenuAuto-Scroll 1 Second Delay Paper Out Fault FinishTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255Top Oversized Off User Language EnglishSize 8192 Characters Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting Advanced Setup Features Security MenuALIGN/ITEM Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when