Printek 850 Series manual ETX/ACK Off, Parallel/LAN Interface Items

Page 57

S P E C I F Y I N G F O R M S

ETX/ACK Handshaking

Possible Values: Off*, On

ETX/ACK Off

Enables or disables the ACK response to receipt of the ETX character. This handshake method is useful for conditions where there are long transmission line delays such as telephone lines, which may be routed through satellites. An ACK character will be returned to the host computer after an ETX character is received and processed. ETX characters used for handshaking cannot be part of an escape sequence.

RTS/CTS Handshaking

Possible Values: Power On/Off*

RTS/CTS OFF

If your Host system requires or supports hardware handshaking for data flow control, it may be useful to change this parameter to ON. This may apply especially to older Host systems using Full-duplex communications.

Parallel/LAN Interface Items

Since the optional LAN interface goes into the Parallel port, these interface parameters are the same.

INTERFACE MENU

Parallel/LAN

4 9

Image 57

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Forms Menu Introduction To SetupInterface Menu Test MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O Interface Set Up RS-232C Serial InterfaceParallel Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print Aligning Print On InvoicesLeft/Right ←0.00→ Left/Right ⎯0.30→ Down/UpCommon Error Conditions Down/Up 0.08 ↓Check Paper No Paper to Load Too Much Paper to UnloadSelected Form is not Loaded Ribbon Lid Open Other ErrorsPrinter Configuration Introduction To SetupSetup Buttons Entering Setup Menus Entering SetupUsing the Menu Button FormUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Using the Submenu ButtonExiting Setup Exiting Menus Saving Changes No ChangesForms Menu Forms Menu ItemsForm Name Tractor Path Rear FormForm Length 66 Lines Lines/InchTop Margin 0 Lines Bottom Margin 0 LinesCharacters/Inc h Left Margin ColumnRight Margin Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalInterface Menu Entering the Interface MenuSerial Interface Menu Serial Emulation Epson RS-232C Serial Interface ItemsAuto CR On Auto LF Off Host FF at TOF No Characters Control Minimum Buffer No Data Bits Baud RateStop Bits Parity NoneDTR Power On/Off Busy Polarity LowXON/XOFF Off ETX/ACK Off Parallel/LAN Interface ItemsParallel/LAN LAN Setup Off Emulation EpsonIP Address Auto IP Address Subnet MaskIP Gateway Auto LF Off Max Form Allowed Options MenuAuto-Scroll 1 Second Delay Paper Out Fault FinishTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255Top Oversized Off User Language EnglishSize 8192 Characters Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting Advanced Setup Features Security MenuALIGN/ITEM Edit Allowed Forms Menu Edit Allowed Interface Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when