Printek 850 Series manual Baud Rate, Data Bits, Stop Bits, Parity None

Page 55

S P E C I F Y I N G F O R M S

Baud Rate

Baud Rate 9600

Possible Values: 110, 150, 300, 600, 1200, 2400, 4800, 9600*

This item selects the baud rate for the serial interface. This must be set to match the baud rate setting on the host computer.

Data Bits

Data Bits 8

Possible Values: 8*, 7

This item selects the number of data bits in the serial character frame. This must be set to match the character size setting on the host computer.

Stop Bits

Possible Values: 1*, 2

Stop Bits 1

This item sets the number of stop bits to be used at the end of the serial character frame. This must be set to match the stop bit setting on the host computer.

Parity

Possible Values: None*, Even, Odd

Parity None

This item selects the parity checking requirements for the serial data bits. This must be set to match the parity setting on the host computer.

4 7

Image 55

Contents PrintMaster 850 Series Operator’s Manual Page Page Page Table of Contents Test Menu Introduction To SetupForms Menu Interface MenuAscii Character Tables Specifications Glossary of Terms Page Introduction Manual Contents Lists Getting Started InstallationParallel I/O Serial I/O RS-232C Serial Interface Interface Set UpParallel Interface Ethernet 10/100BaseT Why Use Only Printek Brand Ribbons Installing The Ribbon CartridgeT T I N G S T a R T E D Installing a New Ribbon Cartridge T T I N G S T a R T E D PrintMaster 850/850si Single Tractor Model Loading PaperInforming the Printer That the New Form is Loaded PrintMaster 852si Dual Tractor Model Selecting Which Form to Print Printer Self-Test Close the front lid and press the Online button Page Introduction Daily OperationLCD Display and Online Status Indicator LED Control Panel FeaturesDisplay the following information Exposed Buttons Most commonly used functions LOAD/FEED Unload Hidden Under LID Buttons SetupSelecting and Loading Forms Loading a New or Different Form In the Tractors Selecting a Form Already Loaded in the TractorsEjecting and Tearing Off a Form Tearing off a Form Aligning Print On Invoices Aligning PrintLeft/Right ←0.00→ Left/Right ⎯0.30→ Down/UpDown/Up 0.08 ↓ Common Error ConditionsCheck Paper Too Much Paper to Unload No Paper to LoadSelected Form is not Loaded Ribbon Lid Open Other ErrorsIntroduction To Setup Printer ConfigurationSetup Buttons Form Entering SetupEntering Setup Menus Using the Menu ButtonExiting Menus Saving Changes No Changes Using the Submenu ButtonUsing the ALIGN/ITEM and UP/DOWN Arrow Buttons Exiting SetupForms Menu Items Forms MenuForm Name Tractor Path Rear FormBottom Margin 0 Lines Lines/InchForm Length 66 Lines Top Margin 0 LinesLeft Margin Column Characters/Inc hRight Margin Draft Speed Normal Font Epson FX FDLanguage Impact Force NormalUnidirectional No Zero NormalEntering the Interface Menu Interface MenuSerial Auto LF Off RS-232C Serial Interface ItemsInterface Menu Serial Emulation Epson Auto CR OnCharacters Control Host FF at TOF NoMinimum Buffer No Parity None Baud RateData Bits Stop BitsBusy Polarity Low DTR Power On/OffXON/XOFF Off Parallel/LAN Interface Items ETX/ACK OffParallel/LAN Emulation Epson LAN Setup OffIP Address Auto Subnet Mask IP AddressIP Gateway Auto LF Off Max Form Allowed Options MenuPaper Out Fault Finish Auto-Scroll 1 Second DelayTear-Off 0.00 Inches Cannot Reprint Page Too Large will be displayed, Top of Barcode Off Char. To Ignore 255User Language English Top Oversized OffSize 8192 Characters Bottom Slew Fast Truncate Lines NoPrint Menus Test Mode OffForm Construction Form Construction and Layout TipsForm Layout Considerations E C I F Y I N G F O R M S Error Messages Maintenance TroubleshootingObtaining Service Preventive MaintenanceI N T E N a N C E a N D Troubleshooting Security Menu Advanced Setup FeaturesALIGN/ITEM Edit Allowed Interface Menu Edit Allowed Forms Menu Edit AllowedOptions Menu Edit Allowed Using Remote Setup V a N C E D S E T U P F E a T U R E S Remote Setup Line Definitions V a N C E D S E T U P F E a T U R E S Remote Setup Example File V a N C E D S E T U P F E a T U R E S Using the Optional Setup Module New Setup Module Detected Initializing Setup ModuleCopying Setup To Module Copying Setup to PrinterI N G T H E O P T I O N a L S E T U P M O D U L E Printer Reset Conditions Genicom 3840 and 3410 Emulation Control Code Escape Sequence SummariesAnsi X3.64 Emulation ESC * m n1 n2 data Epson FX EmulationESC K n1 n2 data IBM Proprinter Emulation LA-120/210 Emulation Printek Emulation Simple TTY EmulationXoff Ascii Character Tables PC Font Character Set Ebcdic Font Character Set C I I C H a R a C T E R T a B L E S OCR-B Font Character Set ML Euro C I I C H a R a C T E R T a B L E S 60 to 240 dpi horizontally x 72 dpi vertically Specifications6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi 15,000,000 character, mobius loop cartridge Operator CONTROLS/INDICATORS Use of only Printek brand ribbons Specification S Ascii Glossary of TermsLCD Online Refers to the state of the printer when