Savin 2545/2545p, 3502/3502p, 4502/4502p, 2235, 2245, 2535/2535p Non-recommended Paper, Paper Storage

Page 39

AdonisC2_ENcopy122F_FM.book Page 26 Thursday, February 15, 2001 3:23 PM

Basics

Non-recommended Paper

RCAUTION:

1• Do not use aluminum foil, carbon paper, or similar conductive paper to avoid a fire or equipment failure.

Important

❒Do not use any of the following kinds of paper or a fault might occur.

•Thermal fax paper

•Art paper

•Aluminum foil

•Carbon paper

•Conductive paper

•Colored OHP transparencies

•Paper with perforated lines

•Hemmed paper

Note

❒Do not use the following kinds of paper or a misfeed might occur.

•Bent, folded, or creased paper

•Torn paper

•Slippery paper

•Perforated paper

•Rough paper

•Thin paper that has low stiffness

•Paper with much paper dust on its surface

❒If you make a copy on rough grain paper, the copy image might be blurred.

Paper Storage

Note

❒When storing paper, the following precautions should always be followed:

•Do not store paper where it will be exposed to direct sunlight.

•Avoid storing paper in humid areas (humidity: 70% or less).

•Store on a flat surface.

❒Keep open reams of papers in the package, and store as you would unopened paper.

❒Under high temperature and high humidity, or low temperature and low hu- midity conditions, store paper in a vinyl bag.

26

Image 39

Contents Zdsh000j.eps ⇒ P.237 Power Connection FCC Requirements Means Power ON. c means Stand bySafety During Operation Safety InformationPage Limitation How to Read this ManualSymbols PreparationTable of Contents Sort/Stack/Staple Job Preset Other FunctionsPreset Reduce/Enlarge Basic Functions121 101112 116161 149151 156207 198202 206239 235236 238Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.77 ⇒ P.39⇒ P.37 103Guide To Components Ventilation hole Bypass tray Right side coverOutput Tray Guide To copy onto normal paper and thick paperTo copy onto OHP transparencies and translucent paper Options Control Panel Function keys Function Status indicatorClear/Stop key Number keysDisplay Panel Displays and Key OperationsInitial copy display Document Server initial display Function menuFunction List Based on Options Set the paper of the same size KL in the paper trays Main power switch left side of the ma- chine Turning On the PowerTurning On the Main Power Operation switch right side of the control panelTurning On the Power Turning Off the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Non-recommended originals for the document feeder OriginalsMetric version Inch versionSizes difficult to detect Sizes Detectable by the Auto Paper SelectMissing Image Area Exposure glassDocument feeder Recommended Paper Sizes and Types Copy PaperIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Paper Storage Non-recommended PaperToner Toner StorageUsed Toner Basics Set your originals Basic ProcedureMake sure that the machine is in Copy mode Make sure that there are no previ- ous settings remainingSystem Reset Lower the platen cover or docu- ment feeder Setting OriginalsSetting Originals on the Exposure Glass Lift the platen cover or the docu- ment feederTurn Setting Originals Document FeederOriginal Orientation Standard OrientationPress the Batch key Setting Special OriginalsBatch mode Press the key Press the OK keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Make sure that the Auto Image Den- sity key is selected Press the Lighter or Darker key to adjust the densitySelecting Original Type Setting Selecting Copy Paper Auto Paper SelectManual Paper Select Make sure that the Auto Paper Select key is selected Auto Paper SelectRotated copy Auto Reduce/Enlarge Press the Auto Reduce/Enlarge keySelect the paper tray Stack Sort/Stack/StapleSort Press the Sort or Rotate Sort key Shift SortAfter all originals are scanned, press the # key When the 2 Tray Finisher is installedEnter the number of copy sets with the number keys Set the original, then press the Start keyStack Shift StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Tray Finisher Sheet FinisherSort/Stack/Staple Select one of the stapling positions⇒ P.51 Stapling position and original setting Press the Yes key When Memory Reaches 0%To Remove the Paper from the Staple Unit Press the No key to resume scanningHoles PunchPunch hole positions Select the Punch position Punchable paper sizes are as followsEnter the number of copy sets with the number keys Open the bypass tray Adjust the guides to copy paper size Copying from the Bypass TrayExtender Press the # key When copying onto custom size paperCopying When Copying onto OHP Transparencies or Thick Paper Select OHP Sheet or Thick PaperPress the OK key Set your originals and press the Start key Deleting a Program Storing Your SettingsPrograms Storing a ProgramPress the Do not Register key Make sure the program settingsDeleting a Program Repeat steps E and F in Storing a ProgramRecalling a Program Press the To Printing key Job PresetPress the Copy key Set up the next copy job Cancel keyPress the Interrupt key Energy Saver Mode Interrupt CopyOther Functions To interrupt an original being fedSet your original Press the Start key Original BeeperSample Copy To interrupt copying after all originals have been fedPress the Clear/Stop key when Copying is displayed Press the Continue keyPress the Change Quantity key Ratio % Paper size Preset Reduce/EnlargeCreate Margin mode Press the Reduce/Enlarge keyPress the Enlarge or Reduce key Press the Mag. Ratio key Adjust the ratios with the n or o keyZoom Enter the ratioEnter the desired ratio with the number keys Press the Reduce/Enlarge key Press the Specifid Ratio key Size MagnificationPress the OK key Set your original, then press the Start key