Savin 4502/4502p, 3502/3502p, 2235, 2545/2545p, 2245 manual Copying from the Bypass Tray, Extender

Page 73

AdonisC2_ENcopy122F_FM.book Page 60 Thursday, February 15, 2001 3:23 PM

Copying

Copying from the Bypass Tray

2

Use the bypass tray to copy onto OHP transparencies, adhesive labels, trans- lucent paper, postcards, and copy pa- per that cannot be set in the paper tray.

Note

❒ The machine can automatically de- tect the following sizes as standard size copy paper:

Metric	L		L			L 1			⋅		L
version	A3	, A4			, A5		, 8 /2"				13"
version

Inch	A3	L		⋅	17"	L	1	⋅			L
version	A3	, 11"			17"	, 8 /2"				14" ,
version	81/2" ⋅ 11"L, 51/2" ⋅ 81/2"L

❒ If you do not use the standard size copy paper, you should input ver- tical and horizontal dimensions. The sizes that you can input are as follows:

Metric	• Vertical: 100 – 297mm
version	• Horizontal: 148 – 600mm

Inch	•	Vertical: 3.9" – 11.6"
version	•	Horizontal: 5.8" – 23.4"

A Open the bypass tray.

B Adjust the guides to copy paper size.

Important

❒If the guides are not flush with the copy paper, a skew image or paper misfeeds might occur.

C Lightly insert the copy paper face up until the beeper sounds.

The k indicator on the display au- tomatically goes on.

60

❒When using paper larger than 433

mmin size, set it so that it is fed straight into the machine.

❒When using paper larger than 433

mmin size, the paper may become wrinkled, and may not be fed into the machine, or may cause paper jams.

❒To make copies onto OHP trans- parencies or thick paper exceeding

128g/m2, 35 lb., specify the paper type in ⇒ P.63 “When Copying onto OHP Transparencies or Thick Paper”.

❒The maximum number of sheets you can set at a time depends on the paper type. For details about

paper capacity of the bypass tray,

⇒ P.22 “Copy Paper”.

1.Extender

Note

❒The face side of the paper set is copied on.

❒Do not stack paper over the lim- it mark, otherwise a skew image or paper misfeeds might occur.

Image 73

Contents Zdsh000j.eps ⇒ P.237 Power Connection FCC Requirements Means Power ON. c means Stand bySafety During Operation Safety InformationPage Symbols How to Read this ManualPreparation LimitationTable of Contents Preset Reduce/Enlarge Job Preset Other FunctionsBasic Functions Sort/Stack/Staple112 101116 121151 149156 161202 198206 207236 235238 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.37 ⇒ P.39103 ⇒ P.77Guide To Components Ventilation hole Bypass tray Right side coverTo copy onto normal paper and thick paper Output Tray GuideTo copy onto OHP transparencies and translucent paper Options Control Panel Clear/Stop key Function Status indicatorNumber keys Function keysDisplays and Key Operations Display PanelInitial copy display Document Server initial display Function menuFunction List Based on Options Set the paper of the same size KL in the paper trays Turning On the Main Power Turning On the PowerOperation switch right side of the control panel Main power switch left side of the ma- chineTurning Off the Power Turning On the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Metric version OriginalsInch version Non-recommended originals for the document feederSizes difficult to detect Sizes Detectable by the Auto Paper SelectExposure glass Missing Image AreaDocument feeder Recommended Paper Sizes and Types Copy PaperIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Paper Storage Non-recommended PaperToner Storage TonerUsed Toner Basics Make sure that the machine is in Copy mode Basic ProcedureMake sure that there are no previ- ous settings remaining Set your originalsSystem Reset Setting Originals on the Exposure Glass Setting OriginalsLift the platen cover or the docu- ment feeder Lower the platen cover or docu- ment feederOriginal Orientation Setting Originals Document FeederStandard Orientation TurnBatch mode Setting Special OriginalsPress the key Press the OK key Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Make sure that the Auto Image Den- sity key is selected Press the Lighter or Darker key to adjust the densitySelecting Original Type Setting Auto Paper Select Selecting Copy PaperManual Paper Select Make sure that the Auto Paper Select key is selected Auto Paper SelectRotated copy Press the Auto Reduce/Enlarge key Auto Reduce/EnlargeSelect the paper tray Stack Sort/Stack/StapleSort Press the Sort or Rotate Sort key Shift SortEnter the number of copy sets with the number keys When the 2 Tray Finisher is installedSet the original, then press the Start key After all originals are scanned, press the # keyShift Stack StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Tray Finisher Sheet FinisherSort/Stack/Staple Select one of the stapling positions⇒ P.51 Stapling position and original setting To Remove the Paper from the Staple Unit When Memory Reaches 0%Press the No key to resume scanning Press the Yes keyHoles PunchPunch hole positions Select the Punch position Punchable paper sizes are as followsEnter the number of copy sets with the number keys Copying from the Bypass Tray Open the bypass tray Adjust the guides to copy paper sizeExtender Press the # key When copying onto custom size paperCopying Select OHP Sheet or Thick Paper When Copying onto OHP Transparencies or Thick PaperPress the OK key Set your originals and press the Start key Programs Storing Your SettingsStoring a Program Deleting a ProgramDeleting a Program Make sure the program settingsRepeat steps E and F in Storing a Program Press the Do not Register keyRecalling a Program Press the Copy key Set up the next copy job Job PresetCancel key Press the To Printing keyOther Functions Energy Saver Mode Interrupt CopyTo interrupt an original being fed Press the Interrupt keySample Copy Original BeeperTo interrupt copying after all originals have been fed Set your original Press the Start keyPress the Continue key Press the Clear/Stop key when Copying is displayedPress the Change Quantity key Ratio % Paper size Preset Reduce/EnlargePress the Reduce/Enlarge key Create Margin modePress the Enlarge or Reduce key Zoom Adjust the ratios with the n or o keyEnter the ratio Press the Mag. Ratio keyEnter the desired ratio with the number keys Press the Reduce/Enlarge key Press the Specifid Ratio key Size MagnificationPress the OK key Set your original, then press the Start key