Savin 2535/2535p, 3502/3502p, 2235 Selecting Copy Paper, Auto Paper Select, Manual Paper Select

Page 53

AdonisC2_ENcopy122F_FM.book Page 40 Thursday, February 15, 2001 3:23 PM

2

Copying

Selecting Copy Paper

There are two ways to select copy paper:

❖Auto Paper Select

The machine selects a suitable size of copy paper automatically based on the original size and the reproduction ratio. ⇒ P.42 “Rotated copy”.

❖ Manual Paper Select

Choose the tray containing the paper you wish to copy onto: Paper Tray, By- pass Tray or large capacity tray (LCT).

Reference

⇒ P.60 “Copying from the Bypass Tray”.

Limitation

❒Auto Paper Select mode is intended for normal and recycled paper.

❒If you set all the paper trays other than “No Display” or “Recycled Paper”, you cannot use Auto Paper Select.

Note

❒See the following table for possible copy paper sizes and directions with Auto Paper Select (when copying at a ratio of 100%):

❖ Metric version

Where Original Is Set	Paper Size and Direction

Exposure glass	A3L, B4L, A4KL, B5KL

Document feeder	A3L, B4L, A4KL, B5KL, A5KL,
	11" ⋅ 17"L, 81/2" ⋅ 11"KL

❖ Inch version

Where Original Is Set

Paper Size and Direction

Exposure glass

11"

⋅

L

1

/2"

⋅

L

1

/2"

⋅

11"

KL

17" , 8

14" , 8

Document feeder

A4

KL

, 11"

⋅

17"

L

1

/2"

⋅

14"

L

, 8

,

81/2" ⋅ 11"KL, 51/2" ⋅ 81/2"KL

❒For some originals, the original size might not be detected correctly. ⇒ P.20 “Sizes difficult to detect”.

❒When you set special paper, such as recycled paper, in the paper tray, you can have the paper type shown on the display. ⇒ “Special Paper Indication” in the System Settings manual.

40

Image 53

Contents Zdsh000j.eps ⇒ P.237 Power Connection FCC Requirements Means Power ON. c means Stand bySafety During Operation Safety InformationPage Symbols How to Read this ManualPreparation LimitationTable of Contents Preset Reduce/Enlarge Job Preset Other FunctionsBasic Functions Sort/Stack/Staple112 101116 121151 149156 161202 198206 207236 235238 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.37 ⇒ P.39103 ⇒ P.77Guide To Components Ventilation hole Bypass tray Right side coverTo copy onto OHP transparencies and translucent paper Output Tray GuideTo copy onto normal paper and thick paper Options Control Panel Clear/Stop key Function Status indicatorNumber keys Function keysInitial copy display Display PanelDisplays and Key Operations Document Server initial display Function menuFunction List Based on Options Set the paper of the same size KL in the paper trays Turning On the Main Power Turning On the PowerOperation switch right side of the control panel Main power switch left side of the ma- chinePress the operation switch to make the On indicator goes on Turning On the PowerTurning Off the Power Turning Off the Main Power Changing Modes Metric version OriginalsInch version Non-recommended originals for the document feederSizes difficult to detect Sizes Detectable by the Auto Paper SelectDocument feeder Missing Image AreaExposure glass Recommended Paper Sizes and Types Copy PaperIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Paper Storage Non-recommended PaperUsed Toner TonerToner Storage Basics Make sure that the machine is in Copy mode Basic ProcedureMake sure that there are no previ- ous settings remaining Set your originalsSystem Reset Setting Originals on the Exposure Glass Setting OriginalsLift the platen cover or the docu- ment feeder Lower the platen cover or docu- ment feederOriginal Orientation Setting Originals Document FeederStandard Orientation TurnBatch mode Setting Special OriginalsPress the key Press the OK key Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Make sure that the Auto Image Den- sity key is selected Press the Lighter or Darker key to adjust the densitySelecting Original Type Setting Manual Paper Select Selecting Copy PaperAuto Paper Select Make sure that the Auto Paper Select key is selected Auto Paper SelectRotated copy Select the paper tray Auto Reduce/EnlargePress the Auto Reduce/Enlarge key Stack Sort/Stack/StapleSort Press the Sort or Rotate Sort key Shift SortEnter the number of copy sets with the number keys When the 2 Tray Finisher is installedSet the original, then press the Start key After all originals are scanned, press the # keyEnter the number of copies with the number keys StackShift Stack Set the original in the same direction as the first one Staple Stapling position and original setting Tray Finisher Sheet FinisherSort/Stack/Staple Select one of the stapling positions⇒ P.51 Stapling position and original setting To Remove the Paper from the Staple Unit When Memory Reaches 0%Press the No key to resume scanning Press the Yes keyHoles PunchPunch hole positions Select the Punch position Punchable paper sizes are as followsEnter the number of copy sets with the number keys Extender Open the bypass tray Adjust the guides to copy paper sizeCopying from the Bypass Tray Press the # key When copying onto custom size paperCopying Press the OK key Set your originals and press the Start key When Copying onto OHP Transparencies or Thick PaperSelect OHP Sheet or Thick Paper Programs Storing Your SettingsStoring a Program Deleting a ProgramDeleting a Program Make sure the program settingsRepeat steps E and F in Storing a Program Press the Do not Register keyRecalling a Program Press the Copy key Set up the next copy job Job PresetCancel key Press the To Printing keyOther Functions Energy Saver Mode Interrupt CopyTo interrupt an original being fed Press the Interrupt keySample Copy Original BeeperTo interrupt copying after all originals have been fed Set your original Press the Start keyPress the Change Quantity key Press the Clear/Stop key when Copying is displayedPress the Continue key Ratio % Paper size Preset Reduce/EnlargePress the Enlarge or Reduce key Create Margin modePress the Reduce/Enlarge key Zoom Adjust the ratios with the n or o keyEnter the ratio Press the Mag. Ratio keyEnter the desired ratio with the number keys Press the Reduce/Enlarge key Press the Specifid Ratio key Size MagnificationPress the OK key Set your original, then press the Start key