Savin 2545/2545p, 2235 Other Functions, Energy Saver Mode Interrupt Copy, Press the Interrupt key

Page 81

AdonisC2_ENcopy122F_FM.book Page 68 Thursday, February 15, 2001 3:23 PM

Copying

Other Functions

Energy Saver Mode

Interrupt Copy

If you do not operate the machine for a certain period after copying, or

2 when you press the {Energy Saver} key, the display disappears and the machine enters Energy Saver mode. When you press the {Energy Saver} key again, the machine returns to the ready condition. In Energy Saver mode, the machine uses less electrici- ty.

Note

❒If you press the {Energy Saver} key during the operation, the current settings will be cleared.

❒It takes about 3 seconds to return to the ready condition from Energy Saver mode.

Reference

⇒“Low Power Timer” in the Sys- tem Settings manual.

68

Use this function if you wish to inter- rupt a long copy job to make urgently needed copies.

Limitation

❒You cannot use the Interrupt Copy function when scanning fax originals.

Note

❒The procedure for making inter- rupt copies depends on which kind of operation the machine is currently carrying out.

To interrupt an original being fed

A Press the {Interrupt} key.

The Interrupt indicator goes on and scanning stops.

B Remove the originals that were being copied and set the originals you wish to copy.

C Press the {Start} key.

The machine starts making your copies.

D When your copy job is finished, remove your originals and copies.

E Press the {Interrupt} key again. The Interrupt indicator goes off.

F When the display prompts you to, replace the originals that were be- ing copied before.

G Press the {Start} key.

The previous copy job settings will be restored and the machine will con- tinue copying from where it left off.

Image 81

Contents Zdsh000j.eps ⇒ P.237 Power Connection FCC Requirements Means Power ON. c means Stand bySafety During Operation Safety InformationPage Symbols How to Read this ManualPreparation LimitationTable of Contents Preset Reduce/Enlarge Job Preset Other FunctionsBasic Functions Sort/Stack/Staple112 101116 121151 149156 161202 198206 207236 235238 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.37 ⇒ P.39103 ⇒ P.77Guide To Components Ventilation hole Bypass tray Right side coverOutput Tray Guide To copy onto normal paper and thick paperTo copy onto OHP transparencies and translucent paper Options Control Panel Clear/Stop key Function Status indicatorNumber keys Function keysDisplay Panel Displays and Key OperationsInitial copy display Document Server initial display Function menuFunction List Based on Options Set the paper of the same size KL in the paper trays Turning On the Main Power Turning On the PowerOperation switch right side of the control panel Main power switch left side of the ma- chineTurning On the Power Turning Off the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Metric version OriginalsInch version Non-recommended originals for the document feederSizes difficult to detect Sizes Detectable by the Auto Paper SelectMissing Image Area Exposure glassDocument feeder Recommended Paper Sizes and Types Copy PaperIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Paper Storage Non-recommended PaperToner Toner StorageUsed Toner Basics Make sure that the machine is in Copy mode Basic ProcedureMake sure that there are no previ- ous settings remaining Set your originalsSystem Reset Setting Originals on the Exposure Glass Setting OriginalsLift the platen cover or the docu- ment feeder Lower the platen cover or docu- ment feederOriginal Orientation Setting Originals Document FeederStandard Orientation TurnBatch mode Setting Special OriginalsPress the key Press the OK key Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Make sure that the Auto Image Den- sity key is selected Press the Lighter or Darker key to adjust the densitySelecting Original Type Setting Selecting Copy Paper Auto Paper SelectManual Paper Select Make sure that the Auto Paper Select key is selected Auto Paper SelectRotated copy Auto Reduce/Enlarge Press the Auto Reduce/Enlarge keySelect the paper tray Stack Sort/Stack/StapleSort Press the Sort or Rotate Sort key Shift SortEnter the number of copy sets with the number keys When the 2 Tray Finisher is installedSet the original, then press the Start key After all originals are scanned, press the # keyStack Shift StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Tray Finisher Sheet FinisherSort/Stack/Staple Select one of the stapling positions⇒ P.51 Stapling position and original setting To Remove the Paper from the Staple Unit When Memory Reaches 0%Press the No key to resume scanning Press the Yes keyHoles PunchPunch hole positions Select the Punch position Punchable paper sizes are as followsEnter the number of copy sets with the number keys Open the bypass tray Adjust the guides to copy paper size Copying from the Bypass TrayExtender Press the # key When copying onto custom size paperCopying When Copying onto OHP Transparencies or Thick Paper Select OHP Sheet or Thick PaperPress the OK key Set your originals and press the Start key Programs Storing Your SettingsStoring a Program Deleting a ProgramDeleting a Program Make sure the program settingsRepeat steps E and F in Storing a Program Press the Do not Register keyRecalling a Program Press the Copy key Set up the next copy job Job PresetCancel key Press the To Printing keyOther Functions Energy Saver Mode Interrupt CopyTo interrupt an original being fed Press the Interrupt keySample Copy Original BeeperTo interrupt copying after all originals have been fed Set your original Press the Start keyPress the Clear/Stop key when Copying is displayed Press the Continue keyPress the Change Quantity key Ratio % Paper size Preset Reduce/EnlargeCreate Margin mode Press the Reduce/Enlarge keyPress the Enlarge or Reduce key Zoom Adjust the ratios with the n or o keyEnter the ratio Press the Mag. Ratio keyEnter the desired ratio with the number keys Press the Reduce/Enlarge key Press the Specifid Ratio key Size MagnificationPress the OK key Set your original, then press the Start key