Savin 2245, 2235 Size Magnification, Press the Reduce/Enlarge key Press the Specifid Ratio key

Page 88

AdonisC2_ENcopy122F_FM.book Page 75 Thursday, February 15, 2001 3:23 PM

Size Magnification

Size Magnification

This function calculates an enlarge- ment or reduction ratio based upon the lengths of the original and copy.

Amm

amm

Preparation

Measure and specify the lengths of the original and copy by compar- ing “A” with “a.”

Limitation

❒If the calculated ratio is over the maximum or under the minimum ratio, it is corrected within the range of the ratio automatically. However, with some ratios, parts of the image might not be copied or blank margins will appear on copies.

Note

❒A ratio is selected in the range of 25 to 400%.

A Press the [Reduce/Enlarge] key.

B Press the [Specifid Ratio] key.

2

C Make sure that the [Specifid Ratio] key is highlighted.

D Enter the length of the original with the number keys and press the [#] key.

Note

❒You can enter sizes within the following ranges:

Metric	1 – 999mm (in 1mm steps)
version

Inch	0.1" – 99.9" (in 0.1" steps)
version

❒To change the length entered, press the [Clear] or {Clear/Stop} key and enter the new length.

75

Image 88

Contents Zdsh000j.eps ⇒ P.237 Power Connection Means Power ON. c means Stand by FCC RequirementsSafety Information Safety During OperationPage How to Read this Manual SymbolsPreparation LimitationTable of Contents Job Preset Other Functions Preset Reduce/EnlargeBasic Functions Sort/Stack/Staple101 112116 121149 151156 161198 202206 207235 236238 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server ⇒ P.39 ⇒ P.37103 ⇒ P.77Guide To Components Bypass tray Right side cover Ventilation holeTo copy onto normal paper and thick paper Output Tray GuideTo copy onto OHP transparencies and translucent paper Options Control Panel Function Status indicator Clear/Stop keyNumber keys Function keysDisplays and Key Operations Display PanelInitial copy display Function menu Document Server initial displayFunction List Based on Options Set the paper of the same size KL in the paper trays Turning On the Power Turning On the Main PowerOperation switch right side of the control panel Main power switch left side of the ma- chineTurning Off the Power Turning On the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Originals Metric versionInch version Non-recommended originals for the document feederSizes Detectable by the Auto Paper Select Sizes difficult to detectExposure glass Missing Image AreaDocument feeder Copy Paper Recommended Paper Sizes and TypesIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Non-recommended Paper Paper StorageToner Storage TonerUsed Toner Basics Basic Procedure Make sure that the machine is in Copy modeMake sure that there are no previ- ous settings remaining Set your originalsSystem Reset Setting Originals Setting Originals on the Exposure GlassLift the platen cover or the docu- ment feeder Lower the platen cover or docu- ment feederSetting Originals Document Feeder Original OrientationStandard Orientation TurnSetting Special Originals Batch modePress the key Press the OK key Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Press the Lighter or Darker key to adjust the density Make sure that the Auto Image Den- sity key is selectedSelecting Original Type Setting Auto Paper Select Selecting Copy PaperManual Paper Select Auto Paper Select Make sure that the Auto Paper Select key is selectedRotated copy Press the Auto Reduce/Enlarge key Auto Reduce/EnlargeSelect the paper tray Sort/Stack/Staple StackSort Shift Sort Press the Sort or Rotate Sort keyWhen the 2 Tray Finisher is installed Enter the number of copy sets with the number keysSet the original, then press the Start key After all originals are scanned, press the # keyShift Stack StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Sheet Finisher Tray FinisherSelect one of the stapling positions Sort/Stack/Staple⇒ P.51 Stapling position and original setting When Memory Reaches 0% To Remove the Paper from the Staple UnitPress the No key to resume scanning Press the Yes keyPunch HolesPunch hole positions Punchable paper sizes are as follows Select the Punch positionEnter the number of copy sets with the number keys Copying from the Bypass Tray Open the bypass tray Adjust the guides to copy paper sizeExtender When copying onto custom size paper Press the # keyCopying Select OHP Sheet or Thick Paper When Copying onto OHP Transparencies or Thick PaperPress the OK key Set your originals and press the Start key Storing Your Settings ProgramsStoring a Program Deleting a ProgramMake sure the program settings Deleting a ProgramRepeat steps E and F in Storing a Program Press the Do not Register keyRecalling a Program Job Preset Press the Copy key Set up the next copy jobCancel key Press the To Printing keyEnergy Saver Mode Interrupt Copy Other FunctionsTo interrupt an original being fed Press the Interrupt keyOriginal Beeper Sample CopyTo interrupt copying after all originals have been fed Set your original Press the Start keyPress the Continue key Press the Clear/Stop key when Copying is displayedPress the Change Quantity key Preset Reduce/Enlarge Ratio % Paper sizePress the Reduce/Enlarge key Create Margin modePress the Enlarge or Reduce key Adjust the ratios with the n or o key ZoomEnter the ratio Press the Mag. Ratio keyEnter the desired ratio with the number keys Size Magnification Press the Reduce/Enlarge key Press the Specifid Ratio keyPress the OK key Set your original, then press the Start key