Savin 2235, 3502/3502p, 4502/4502p, 2545/2545p When copying onto custom size paper, Press the # key

Page 74

AdonisC2_ENcopy122F_FM.book Page 61 Thursday, February 15, 2001 3:23 PM

Copying from the Bypass Tray

❒If the beeper is turned off, light- ly insert the copy paper until it stops. Refer to the System Set- tings manual.

❒When the document feeder is

open, set the direction of the copy paper to L.

❒Swing out the extender to sup-

port paper sizes larger than A4L, 81/2" ⋅ 11"L.

❒Fan paper to get air between the sheets and avoid a multi-sheet feed.

❒Before setting, adjust the paper if curled or warped.

When copying onto standard size paper (Thick Paper, Thin paper, Transparent Paper, or OHP transparecies)

APress the {#} key.

BPress the [Select Size] key.

C Select the paper size.

Note

❒The copy paper sizes that can be selected are as follows:

•A3L, A4KL, A5KL,

A6 L, B4 L, B5 KL, B6L, 11⋅17L, 81/2⋅14L, 81/2⋅11KL, 51/2⋅81/2L, 71/4⋅101/2L, 8⋅13L,

81/2⋅13L, 81/4⋅13K, 1 1 ⋅ 14 L, 1 1 ⋅ 15 K, 10⋅14L, 10⋅15L,

81/4⋅14L, 8⋅101/2KL, 8⋅10KL

When copying onto custom size paper

Important

❒You should specify the size of copy paper to avoid paper mis- feeds.

A Press the {#} key.

2

61

Image 74

Contents Zdsh000j.eps ⇒ P.237 Power Connection Means Power ON. c means Stand by FCC RequirementsSafety Information Safety During OperationPage Preparation How to Read this ManualSymbols LimitationTable of Contents Basic Functions Job Preset Other FunctionsPreset Reduce/Enlarge Sort/Stack/Staple116 101112 121156 149151 161206 198202 207238 235236 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server 103 ⇒ P.39⇒ P.37 ⇒ P.77Guide To Components Bypass tray Right side cover Ventilation holeTo copy onto OHP transparencies and translucent paper Output Tray GuideTo copy onto normal paper and thick paper Options Control Panel Number keys Function Status indicatorClear/Stop key Function keysInitial copy display Display PanelDisplays and Key Operations Function menu Document Server initial displayFunction List Based on Options Set the paper of the same size KL in the paper trays Operation switch right side of the control panel Turning On the PowerTurning On the Main Power Main power switch left side of the ma- chinePress the operation switch to make the On indicator goes on Turning On the PowerTurning Off the Power Turning Off the Main Power Changing Modes Inch version OriginalsMetric version Non-recommended originals for the document feederSizes Detectable by the Auto Paper Select Sizes difficult to detectDocument feeder Missing Image AreaExposure glass Copy Paper Recommended Paper Sizes and TypesIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Non-recommended Paper Paper StorageUsed Toner TonerToner Storage Basics Make sure that there are no previ- ous settings remaining Basic ProcedureMake sure that the machine is in Copy mode Set your originalsSystem Reset Lift the platen cover or the docu- ment feeder Setting OriginalsSetting Originals on the Exposure Glass Lower the platen cover or docu- ment feederStandard Orientation Setting Originals Document FeederOriginal Orientation TurnPress the key Press the OK key Setting Special OriginalsBatch mode Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Press the Lighter or Darker key to adjust the density Make sure that the Auto Image Den- sity key is selectedSelecting Original Type Setting Manual Paper Select Selecting Copy PaperAuto Paper Select Auto Paper Select Make sure that the Auto Paper Select key is selectedRotated copy Select the paper tray Auto Reduce/EnlargePress the Auto Reduce/Enlarge key Sort/Stack/Staple StackSort Shift Sort Press the Sort or Rotate Sort keySet the original, then press the Start key When the 2 Tray Finisher is installedEnter the number of copy sets with the number keys After all originals are scanned, press the # keyEnter the number of copies with the number keys StackShift Stack Set the original in the same direction as the first one Staple Stapling position and original setting Sheet Finisher Tray FinisherSelect one of the stapling positions Sort/Stack/Staple⇒ P.51 Stapling position and original setting Press the No key to resume scanning When Memory Reaches 0%To Remove the Paper from the Staple Unit Press the Yes keyPunch HolesPunch hole positions Punchable paper sizes are as follows Select the Punch positionEnter the number of copy sets with the number keys Extender Open the bypass tray Adjust the guides to copy paper sizeCopying from the Bypass Tray When copying onto custom size paper Press the # keyCopying Press the OK key Set your originals and press the Start key When Copying onto OHP Transparencies or Thick PaperSelect OHP Sheet or Thick Paper Storing a Program Storing Your SettingsPrograms Deleting a ProgramRepeat steps E and F in Storing a Program Make sure the program settingsDeleting a Program Press the Do not Register keyRecalling a Program Cancel key Job PresetPress the Copy key Set up the next copy job Press the To Printing keyTo interrupt an original being fed Energy Saver Mode Interrupt CopyOther Functions Press the Interrupt keyTo interrupt copying after all originals have been fed Original BeeperSample Copy Set your original Press the Start keyPress the Change Quantity key Press the Clear/Stop key when Copying is displayedPress the Continue key Preset Reduce/Enlarge Ratio % Paper sizePress the Enlarge or Reduce key Create Margin modePress the Reduce/Enlarge key Enter the ratio Adjust the ratios with the n or o keyZoom Press the Mag. Ratio keyEnter the desired ratio with the number keys Size Magnification Press the Reduce/Enlarge key Press the Specifid Ratio keyPress the OK key Set your original, then press the Start key