Savin 3502/3502p, 4502/4502p How to Read this Manual, Symbols, Preparation, Limitation, Reference

Page 6

AdonisC2_ENcopy122F_FM.book Page iii Thursday, February 15, 2001 3:23 PM

How to Read this Manual

Symbols

In this manual, the following symbols are used:

RWARNING:

This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the in- structions under this symbol. Be sure to read the instructions, all of which are in- cluded in the Safety Information section.

RCAUTION:

This symbol indicates a potentially hazardous situation that might result in mi- nor or moderate injury or property damage that does not involve personal injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section.

• WARNINGS and CAUTIONS are notes for your safety.

Important

If this instruction is not followed, paper might be misfeed, originals might be damaged, or data might be lost. Be sure to read this.

Preparation

This symbol indicates the prior knowledge or preparations required before op- erating.

Note

This symbol indicates precautions for operation or actions to take after misoper- ation.

Limitation

This symbol indicates numerical limits, functions that cannot be used together, or conditions in which a particular function cannot be used.

Reference

This symbol indicates a reference.

[ ]

Keys that appear on the machine's display panel.

{}

Keys built into the machine's control panel.

iii

Image 6

Contents Zdsh000j.eps ⇒ P.237 Power Connection Means Power ON. c means Stand by FCC RequirementsSafety Information Safety During OperationPage Preparation How to Read this ManualSymbols LimitationTable of Contents Basic Functions Job Preset Other FunctionsPreset Reduce/Enlarge Sort/Stack/Staple116 101112 121156 149151 161206 198202 207238 235236 239Page Machine Types What You Can Do with This Machine Copy Mode Series/Book Document Server 103 ⇒ P.39⇒ P.37 ⇒ P.77Guide To Components Bypass tray Right side cover Ventilation holeOutput Tray Guide To copy onto normal paper and thick paperTo copy onto OHP transparencies and translucent paper Options Control Panel Number keys Function Status indicatorClear/Stop key Function keysDisplay Panel Displays and Key OperationsInitial copy display Function menu Document Server initial displayFunction List Based on Options Set the paper of the same size KL in the paper trays Operation switch right side of the control panel Turning On the PowerTurning On the Main Power Main power switch left side of the ma- chineTurning On the Power Turning Off the PowerPress the operation switch to make the On indicator goes on Turning Off the Main Power Changing Modes Inch version OriginalsMetric version Non-recommended originals for the document feederSizes Detectable by the Auto Paper Select Sizes difficult to detectMissing Image Area Exposure glassDocument feeder Copy Paper Recommended Paper Sizes and TypesIfy the size. ⇒ P.60 Copying from the Bypass Tray Basics Direction-fixed paper or 2-sided paper Non-recommended Paper Paper StorageToner Toner StorageUsed Toner Basics Make sure that there are no previ- ous settings remaining Basic ProcedureMake sure that the machine is in Copy mode Set your originalsSystem Reset Lift the platen cover or the docu- ment feeder Setting OriginalsSetting Originals on the Exposure Glass Lower the platen cover or docu- ment feederStandard Orientation Setting Originals Document FeederOriginal Orientation TurnPress the key Press the OK key Setting Special OriginalsBatch mode Press the Batch keyMixed Size mode Setting Custom Size Originals Clear or Clear/Stop key, and then enter the value again Basic Functions Press the Lighter or Darker key to adjust the density Make sure that the Auto Image Den- sity key is selectedSelecting Original Type Setting Selecting Copy Paper Auto Paper SelectManual Paper Select Auto Paper Select Make sure that the Auto Paper Select key is selectedRotated copy Auto Reduce/Enlarge Press the Auto Reduce/Enlarge keySelect the paper tray Sort/Stack/Staple StackSort Shift Sort Press the Sort or Rotate Sort keySet the original, then press the Start key When the 2 Tray Finisher is installedEnter the number of copy sets with the number keys After all originals are scanned, press the # keyStack Shift StackEnter the number of copies with the number keys Set the original in the same direction as the first one Staple Stapling position and original setting Sheet Finisher Tray FinisherSelect one of the stapling positions Sort/Stack/Staple⇒ P.51 Stapling position and original setting Press the No key to resume scanning When Memory Reaches 0%To Remove the Paper from the Staple Unit Press the Yes keyPunch HolesPunch hole positions Punchable paper sizes are as follows Select the Punch positionEnter the number of copy sets with the number keys Open the bypass tray Adjust the guides to copy paper size Copying from the Bypass TrayExtender When copying onto custom size paper Press the # keyCopying When Copying onto OHP Transparencies or Thick Paper Select OHP Sheet or Thick PaperPress the OK key Set your originals and press the Start key Storing a Program Storing Your SettingsPrograms Deleting a ProgramRepeat steps E and F in Storing a Program Make sure the program settingsDeleting a Program Press the Do not Register keyRecalling a Program Cancel key Job PresetPress the Copy key Set up the next copy job Press the To Printing keyTo interrupt an original being fed Energy Saver Mode Interrupt CopyOther Functions Press the Interrupt keyTo interrupt copying after all originals have been fed Original BeeperSample Copy Set your original Press the Start keyPress the Clear/Stop key when Copying is displayed Press the Continue keyPress the Change Quantity key Preset Reduce/Enlarge Ratio % Paper sizeCreate Margin mode Press the Reduce/Enlarge keyPress the Enlarge or Reduce key Enter the ratio Adjust the ratios with the n or o keyZoom Press the Mag. Ratio keyEnter the desired ratio with the number keys Size Magnification Press the Reduce/Enlarge key Press the Specifid Ratio keyPress the OK key Set your original, then press the Start key